User manual SHERWOOD RD-5503

[. . . ] OPERATING INSTRUCTIONS RD-5503 SURROUND RECEIVER Introduction READ THIS BEFORE OPERATING YOUR UNIT ENGLISH This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Caution regarding installation Note : For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure. Do not block ventilation openings or stack other equipment on the top. FOR YOUR SAFETY Units shipped to Australia are designed for operation on 230 V AC only. To ensure safe operation, the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth. [. . . ] · Weak stations are skipped during auto tuning. Manual tuning · Manual tuning is useful when you already know the frequency of the desired station. · After selecting the desired band, press the TUNING UP(+) / DOWN(-) buttons repeatedly until the right frequency has been reached. Auto presetting · Auto presetting function automatically searches for FM stations only and store them in the memory. · While listening to radio broadcasts, press and hold down the (MEMORY/) ENTER button for more than 2 seconds. or · Then "AUTO MEM" flickers and this receiver starts auto presetting. · To memorize AM stations or weak stations, preform "Manual presetting" procedure with using "Manual tuning" operation. 20 ENGLISH 1. Press the TUNING UP(+)/DOWN(-) buttons for more Manual presetting · You can store up to 30 preferred stations in the memory. 1. Tune in the desired station with auto or manual tuning. ENGLISH 3. Select the desired preset number (1~30) and press the ENTER button. or 2. Press the ENTER button. · When using the NUMERIC buttons on the remote control. Examples) For "3" : For "15" : For "30" : · The station has now been stored in the memory. · When using the NUMERIC buttons, the station is stored automatically without pressing the ENTER button. · A stored frequency is erased from the memory by storing another frequency in its place. · If "MEM" goes off, start again from the above step 2. MEM DIRECT · "MEM" is flickering for several seconds. 4. Repeat the above steps1 to 3 to memorize other stations. MEMORY BACKUP FUNCTION The following items, set before the receiver is turned off, are memorized. · INPUT SELECTOR settings · Surround mode settings · Preset stations, etc. Tuning to preset stations · After selecting the tuner as an input source, select the desired preset number. Examples) For "3" : For "15" : For "30" : 21 RDS Tuner (Regional Option for some countries in Europe, etc. ) LISTENING TO RDS BROADCASTS(FM ONLY) ENGLISH RDS(Radio Data System) is a method for sending information signals together with the transmitter signals. Your tuner is capable of translating these signals and putting the information on the display. Program Service name (PS), A list of Program Types (PTY), Traffic Announcement (TA), Clock Time (CT), Radio Text (RT). Note : In the other countries, RDS tuner function cannot be available. RDS search · Use this function to automatically search and receive the stations offering RDS services. 1. When "RDS SRCH" is displayed, press the ENTER button. · Each time this button is pressed, the search mode changes as follows; RDS SRCH TP SRCH PTY SRCH OFF · The tuner automatically searches stations offering RDS services and the station name is displayed. · When "RDS SRCH" is not displayed, repeat again from the above step 1. TP search · Use this function to automatically search and receive the stations broadcasting the traffic program. 1. When "TP SRCH" is displayed, press the ENTER button. · "TP SRCH" is displayed. · The tuner automatically searches for stations broadcasting the traffic program. [. . . ] Notes: · The night mode setting is valid only when the digital signals from Dolby Digital program source are being input. · In some Dolby Digital softwares, the night mode setting may not be valid. 1. Press the CURSOR UP( )/DOWN( ) buttons to select the "NIGHT M", then press the ENTER button. 2. Press the CURSOR LEFT( )/ RIGHT( ) buttons to adjust the dynamic range compression as desired. 0. 0 0. 1 0. 2 . . . . . . . . [. . . ]