Detailed instructions for use are in the User's Guide.
[. . . ] R-765
Introduction
READ THIS BEFORE OPERATING YOUR UNIT
ENGLISH
This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
CAUTION
: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Note to CATV System Installer : This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as pracitcal. FCC INFORMATION NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFCATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. [. . . ] Please be sure to unplug the cord when you leave home for, say, a vacation.
or
1
2
3
4
TUNER CD AUX TAPE VIDEO 1 VIDEO 2 VIDEO 3
1
2
3
4
5
6
7
8
5
6
7
8
9
0
+10
9
0
+10
· To switch the power off, push the POWER switch again. · Then the power is cut off and the STANDBY indicator goes off.
· Each time the "AUDIO" button on the front panel is pressed, the input source changes as follows; TUNER CD TAPE AUX
M1 M2 M3 T/V
MACRO
MACRO
M1 M2 M3
T/V
(frequency display)
1
In the standby mode, turn the power on.
· Each time the "VIDEO" button on the front panel is pressed, the input source changes as follows; VIDEO 1 VIDEO 2 VIDEO 3
STANDBY
POWER ON
ON/STANDBY
or
When selecting the 7 CH DIRECT as desired,
INPUT SELECTOR
7CH DIRECT
T/V T/V
1
2
3
4
1
2
3
4
· In the operating mode, if the STANDBY button on the remote control is pressed, the receiver is turned off and enters the standby mode. · In the standby mode, if the INPUT SELECTOR button is pressed, the receiver is turned on automatically and the desired input is selected. Switch the speakers on.
SPEAKER
5
6
7
8
5
6
7
8
or
7 CH IN
9 0
+10
9
0
+10
MACRO
M1 M2 M3 M1
MACRO
M2 M3
2
ON/OFF
1
2
3
4
1
· "7-DIRECT" is displayed and the 7 or 6 separate analog signals from the component connected to this input can be controlled only by channel level(s) and volume depending on the surround back speaker setting. · Press the 7 CH DIRECT button or select the desired input source to cancel the 7 CH direct function. · These analog signals can be heard only, not recorded.
2 3 4 6 7 8 0
+10
5
6
7
8
5
9
0
+10
9
· Then the SPEAKER indicator lights up and the sound can be heard from the speakers connected to the speaker terminals. · When using the headphone for private listening, press the SPEAKER button again to switch the speakers off.
MACRO
M2 M1 M3
MACRO
M1 M2 M3
19
When CD, VIDEO 1~3 is selected as an input source
7
To compensate for edgy or shrill movie sound tracks.
CINEMA EQ
4
Select the digital or analog input connected as desired.
DIGITAL INPUTS
· Each time this button is pressed, the corresponding input is selected as follows ; A(nalog) c(oaxial) 1 c(oaxial) 2 o(ptical) 2 o(ptical) 1 · To listen to a DTS or Dolby Digital program source in the 2-CH downmix mode, in the stereo mode, the corresponding digital input should be selected. (For details, refer to "Downmixing into 2 front channels" on page 31. ) Notes : · When the selected optical or coaxial digital input is not connected, the "DIGITAL" indicator flickers, meaning no sound. (Refer to "ENJOYING SURROUND SOUND" on page 27. ) · The sound from the component connected to the selected digital input can be heard regardless of the selected input source.
· Then "C-EQ OFF" is scrolled. · When 96 kHz PCM(2 CH stereo) signals are input, the cinema EQ function does not work.
8
To mute the sound.
T/V
ENGLISH
T/V
MUTE
· "MUTE" will flicker. · To resume the previous sound level, press it again.
5
Operate the selected component for playback.
9
To listen with the headphones.
PHONES
· When playing back the program sources with surround sound, refer to "ENJOYING SURROUND SOUND" on page 27.
1
2
3
4
1
2
3
5
6
7
8
5
6
7
9
0
+10
9
0
+10
6
DOWN
Adjust the (overall) volume. · When listening to a DTS or Dolby Digital program source, if the headphones are plugged and the SPEAKER button is set to off, it enters the 2-CH downmix mode automatically. (For details, refer to "Downmixing into 2 front channels"on page 31. )
MACRO
M2 M1 M3
T/V
MACRO
M1 M2 M3
MASTER VOLUME
T/V
VOLUME
or
UP
20
1 2 3 4 1 2 3 4
5
6
7
8
5
6
7
8
9
0
+10
9
0
+10
Adjusting the tone(bass and treble)
10
Enter the tone mode.
11
At the desired tone mode, adjust the tone as desired.
ADJUST
TONE MODE
· At "TONE ON" mode, you can select "TONE OFF" mode and vice versa. · Each time this button is pressed, the corresponding tone mode is selected and shown for several seconds as follows: BASS TRBL(treble) TONE ON · When the tone mode is off, "TONE OFF" is shown. ("DIRECT" indicator goes off. ) TONE OFF: When listening to a program source without the tone effect. ("DIRECT" indicator light up. ) · In general, we recommend the bass and the treble to be set to 0(flat) level. Notes: · If the tone display disappears, start from the step 10 again. · When the digital signals from DTS or Dolby Digital program sources are input in available surround mode or the 7 CH DIRECT is selected as an input source, you cannot adjust the tone and can hear a program source without the tone effect.
21
SURROUND SOUND
· This receiver incorporates a sophisticated Digital Signal Processor that allows you to create optimum sound quality and sound atmosphere in your personal Home Theater.
Surround modes
DTS Digital Surround
DTS Digital Surround(also called simply DTS) is a multichannel digital signal format which can handle higher data rates than Dolby Digital. Although both Dolby Digital and DTS are 5. 1 channel formats, discs bearing the " " are generally thought to provide better sound quality due to the lower audio compression required. It also provides wide dynamic range and separation, resulting in magnificent sound.
DTS Neo : 6TM surround
This mode applies conventional 2-channel signals such as digital PCM or analog stereo signals to the high precision digital matrix decoder used for DTS-ES Matrix 6. 1 to achieve 6. 1-channel surround playback. DTS Neo : 6 surround includes two modes for selecting the optimum decoding for the signal source. Decoding is performed with emphasis on separation performance to achieve the same atmosphere with 2-channel sources as with 6. 1-channel sources. [. . . ] · The test tone display will be shown until the test tone mode is canceled.
MENU SCREEN
· This function simplifies the setup procedures. · The menu screen operation is performed easily with the CURSOR control( , , , ), OSD and ENTER buttons.
1
Turn the menu screen on.
T/V
T/V
OSD
· The main menu will be shown. · To turn the menu screen off, press this button.
1
2
3
4
1
2
3
4
5
6
7
8
5
6
7
8
9
0
+10
9
0
+10
MACRO
M1 M2 M3 M1
MACRO
M2 M3
37
T/V
T/V
2 3
Select the desired menu using the CURSOR UP( ) or DOWN( ) button.
CURSOR UP, DOWN
T/V
T/V
Confirm your selection.
ENTER
1
2
3
4
1
2
3
4
5
6
7
8
5
6
7
8
9
0
+10
9
0
+10
MACRO
MACRO
M3 M1 M2 M3
When selecting the SPEAKER SETUP
M1
M2
1
2
3
4
1
2
3
4
5
6
7
8
5
6
7
8
9
0
+10
9
0
+10
MACRO
MACRO
M3 M1 M2 M3
When selecting the FUNCTION SELECT
When selecting the SURROUND MODE
M1 M2
· Only when one of TUNER, CD, TAPE and AUX is selected, you can select a video input source on the VIDEO SELECT menu and enjoy the audio and video signals separately. (In case of selecting TUNER, you cannot enjoy component video signals) · When dubbing them onto VIDEO 1, select either VIDEO 2 or VIDEO 3 on the VIDEO SELECT menu. [. . . ]