User manual SHERWOOD DS-10

[. . . ] DS-10(A)_ENG_090212:DS-10(A)2009-02-19 10:431 DS-10(A)_ENG_090212:DS-10(A)2009-02-19 10:432 IMPORTANT SAFETY INSTRUCTIONS 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] · Do not connect headphones to the DIGI LINK-I jack, it can cause damage to the unit. Sherwood receiver such as RD-7503, etc. 6 DS-10(A)_ENG_090212:DS-10(A)2009-02-19 10:437 2. CONNECTING VIDEO and AUDIO JACKS · The jacks of VIDEO or COMPONENT may also be connected to the Sherwood receiver such as RD-7503 or a TV. · There are two types of video jacks (COMPONENT, (composite) VIDEO) for video connections and L/R jacks for audio connections. Connect them to the corresponding video jacks according to their capability. · When making COMPONENT VIDEO connections, using the supplied COMPONENT VIDEO CONNECTION cable, connect "Green" to "Y", "Blue" to "CB"(or "B-Y", "PB") and "Red" to "CR"(or "R-Y", "PR"). Notes : · When making video and audio connections, you should use the supplied cables. · When the iPod Dock is connected to the DIGI LINK-I jack of Sherwood receiver for system control, you should connect the VIDEO and AUDIO jacks to those of "VIDEO 2" of Sherwood receiver. Because, when you control the iPod with receiver's remote control, the VIDEO 2 is automatically selected as an input source for your iPod and the corresponding operation is performed. (For details, refer to the operating instructions of Sherwood receiver. ) 3. CONNECTING DC IN JACK · Plug the supplied AC adapter into the DC IN jack and then into the wall AC outlet. Notes : · The AC adapter supplied with the iPod Dock is designed exclusively for use with the iPod Dock. VOLUME ( / ) buttons Press these buttons to adjust the volume on the connected receiver. They can't adjust the volume on the iPod. 8 DS-10(A)_ENG_090212:DS-10(A)2009-02-19 10:439 REMOTE CONTROL OPERATION RANGE · Use the remote control within a range of about 5 meters (16 feet) and angles of up to 30 degrees aiming at the remote sensor. Notes : · If the iPod Dock is placed on top of another component, the signal of remote control may be obstructed and the remote control may not work reliably. · If another remote control of the same type is used in the same room or the iPod Dock is installed close to component that uses infrared rays, the remote control may not work reliably. · When the remote control is not used, don't place anything on top of the remote control, such as a book, magazine or etc. , because a button may be pressed continuously, thereby draining the battery. · If the iPod Dock is placed in a rack behind colored glass doors, the remote control may not work reliably. · If there's an obstacle between the iPod Dock's remote sensor and the remote control, the remote control may not work. · The remote control may not work reliably if the iPod Dock is subjected to bright light, such as direct sunlight or invert type fluorescent lights. Remote sensor LOADING BATTERY · When the remote control does not operate, the old battery should be replaced. 1. Load the battery(CR2025) matching the polarity. 3V 3V · Remove the battery when it is not used for a long time. 9 ENGLISH DS-10(A)_ENG_090212:DS-10(A)2009-02-19 10:4310 Operations Note: · Before using this iPod Dock, first set the OSD mode. SETTING THE OSD MODE ENGLISH · Plug in the AC adapter. · Turn on the TV and the receiver, and select the corresponding inputs on TV and the receiver. 3. Press the MODE button to set the OSD mode. 1. Insert your iPod into the iPod Dock. · When the iPod is inserted into the iPod Dock, the iPod is turned on automatically. [. . . ] Direct Change Function(*) · If you start iPod playback while listening to another input source, the receiver will automatically select your iPod as the input source. Using Your Receiver's Remote Control · You can use your receiver's remote control to control basic iPod functions. (For details, refer to "USING THE RECEIVER'S REMOTE CONTROL" on page 16. ) (*) : · If you use your iPod's controls to start an iPod slideshow or video, these functions will not work, so use the remote control instead. Notes: · The iPod Dock must be connected to the receiver with both a Digi Link-I cable and an audio cable to use Digi Link-I functions. [. . . ]