User manual SHARP XV-Z7000 (PART2) USEFUL FEATURES, MAINTENANCE AND TROUBLESHOOTING, APPENDIX

[. . . ] Most suitable when viewing images in a brightly lit room. On-screen Display STANDARD STANDARD GAMMA 1 GAMMA 2 GAMMA 1 1 Press GAMMA on the remote control. Each time GAMMA is pressed, the gamma level toggles as shown on the left. s Useful Features GAMMA 2 s 30 Selecting the Picture Display Mode Projector ON/OFF POWER LAMP Remote control RGB/ INPUT 1 COMPONENT PICT MODE TEMP. KEYSTONE INPUT PICT MODE INPUT 2 AUTO SYNC GAMMA This function allows you to modify or customise the picture display mode to enhance the input image. Depending on the input signal, you can choose the picture display mode preferred. [. . . ] (See pages 38 and 39. ) · Take the projector to your nearest Sharp Authorised LCD Projector Dealer or Service Centre for repair. · Securely install the filter cover. Maintenance Indicator TEMPERATURE WARNING indicator Condition The internal temperature is abnormally high. Problem · Blocked air intake. The indicator flashes in red when the projector is on. · Cooling down. · The filter cover is open. POWER indicator · If the TEMPERATURE WARNING indicator illuminates, follow the solution listed above and then wait until the projector has cooled down completely before turning the power back on. Please have Sharp Authorised LCD Projector Dealer or Service Centre replace lamp if rupture occurs. · Do not remove the lamp cage directly after operation of the projector. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp cage to fully cool before removing the lamp cage. It is recommended that the lamp be replaced after approximately 900 cumulative hours of use or when you notice a significant deterioration of the picture and colour quality. If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorised LCD Projector Dealer or Service Centre for repair. Purchase a replacement lamp unit (lamp/cage module) of the current type BQC-PGC20X//1 from your nearest Sharp Authorised LCD Projector Dealer or Service Centre. If you wish, you may have the lamp replaced at your nearest Sharp Authorised LCD Projector Dealer or Service Centre. Removing and installing the lamp unit CAUTION · Be sure to remove the lamp cage by the handle. Be sure not to touch the glass surface of the lamp cage or the inside of the projector. · To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below. The air filter comes packaged with the lamp unit. First Change Filter (Steps 3-6) 1 Turn off the power. 2 Disconnect the power cord. 3 Remove the filter cover. Press ON/OFF on the projector or POWER on the remote control. Wait until the cooling fan stops. ON/OFF Unplug the power cord from the AC socket. Turn over the projector. Press the tab and remove the filter cover in the direction of the arrow. Tab or POWER VOL POWER MUTE BACK MENU 4 Remove the air filter. 5 Replace the air filter. 6 Replace the filter cover. Maintenance & Troubleshooting 1 Remove the air filter stopper. 2 Put the air filter stopper back into position. Insert the tab on the end of the filter cover into the filter cover opening and press the filter cover into position. Tab ;;;;;; ;;;;; ;;;;;; ; ;;;;; ;;;;;; ;;;;; ;;;;; ;;;;; ;;;;; ;;;;;; ;;;;; ;;;;;; ; ;;;;;; ;;;;;; 38 Replacing the Projection Lamp Then Change Lamp (Steps 7-10) 7 Remove the lamp cage cover. 8 Remove the lamp cage. Turn over the projector and loosen the user service screw that secures the lamp cage cover. Then lift open the cover in the direction of the arrow. Loosen the securing screws on the lamp cage. Hold the lamp cage by the handle and pull it towards you. 9 Insert the new lamp cage. 10 Attach the lamp cage cover. Press the lamp cage firmly into the lamp cage compartment. Fasten the securing screws. Slide the lamp cage cover in the direction of the arrow. Then tighten the user service screw. Resetting the lamp timer 1 Connect the power cord. 2 Reset the lamp timer. "LAMP 0000H" is displayed, indicating that the lamp timer is reset. Plug the power cord into the AC socket of the projector. Maintenance & Troubleshooting 1 Press KEYSTONE and KEYSTONE on the projector at the same time. 3 Press PICT MODE and MENU on the projector at the same time. 1 INPUT PICT MODE 2 BACK ENTER MENU 3 · Reset the lamp timer only after replacing the lamp. 39 Using the Kensington Lock This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. [. . . ] Intelligent compression and expansion High quality resizing of lower and higher resolution images to fit the projector's native resolution. Phase Phase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the projected image typically displays horizontal flicker. Picture display mode Allows you to modify or customise the picture display mode to enhance the input image. [. . . ]