User manual SHARP XV-Z10E
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP XV-Z10E. We hope that this SHARP XV-Z10E user guide will be useful to you.
You may also download the following manuals related to this product:
SHARP XV-Z10E (6259 ko)
SHARP XV-Z10E (7079 ko)
SHARP XV-Z10E (7194 ko)
SHARP XV-Z10E (6581 ko)
SHARP XV-Z10E (4171 ko)
SHARP XV-Z10E (6860 ko)
SHARP XV-Z10E (6581 ko)
SHARP XV-Z10E (6860 ko)
SHARP XV-Z10E (6800 ko)
SHARP XV-Z10E (4171 ko)
SHARP XV-Z10E (7079 ko)
SHARP XV-Z10E (6544 ko)
SHARP XV-Z10E OPERATION MANUAL (6792 ko)
Manual abstract: user guide SHARP XV-Z10E
Detailed instructions for use are in the User's Guide.
[. . . ] XV-Z10E
PROJECTOR PROJEKTOR PROJECTEUR PROJEKTOR PROYECTOR PROIETTORE PROJECTOR OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI BRUKSANVISNING MANUAL DE MANEJO MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING
ENGLISH . . . . . . . . . . . . . NEDERLANDS . . . .
-1 -1 -1 -1 -1 -1 -1
-68 -68 -68 -68 -68 -68 -68
This equipment complies with the requirements of Directive 89/336/EEC and 73/23/EEC as amended by 93/68/EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE. [. . . ] Used for projecting images from equipment connected to the INPUT 3 terminal. INPUT 3 mode Using Video Using RGB
INPUT 2 mode Using S-Video
Basic Operation
Volume buttons
Adjusting the Volume
Press or on the remote control to adjust the volume.
Note
· Pressing will lower the volume. · On the projector, the volume can be adjusted by pressing or .
Volume buttons
"On-screen Display
-27
Image Projection
Turning off the Sound Temporarily
Press on the remote control to temporarily turn off the sound.
Note
· Pressing on. again will turn the sound back
"On-screen Display
MUTE button
Turning the Power off
(Putting STANDBY button
the Projector into the Standby Mode)
1
Press
on the projector or on the remote control, then press that button again while the confirmation message is displayed, to put the projector into the standby mode.
"On-screen Display
Note
· If you accidentally pressed or and do not want to put the projector into the standby mode, wait until the confirmation message disappears.
2
Unplug the power cord from the wall outlet after the cooling fan stops.
Info
· Do not unplug the power cord during projection or cooling fan operation. The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode. This can cause damage due to rise in internal temperature, as the cooling fan also stops.
-28
Correcting Trapezoidal Distortion
When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.
', ", \, |
buttons
KEYSTONE button
UNDO button
Note
· The Keystone Correction can be adjusted up to an angle of approximately ±30 degrees and the screen can also be set up to an angle of approximately ±30 degrees (when the resize mode is set to "STRETCH" for the video signal input or "SIDE BAR" for the computer signal input). · The Keystone Correction cannot be adjusted in the lateral direction. · For details about the setup, see pages 7 and 16.
UNDO button
', ", \, |
buttons
"On-screen display (Keystone Correction mode)
1
Basic Operation
Press to enter the Keystone Correction mode.
· The on-screen display of the Keystone Correction mode will appear.
Compresses upper side.
2
Press ', ", \ and | to adjust the Keystone Correction.
· You can also adjust the Keystone Correction using the , tons on the projector. · Straight lines or the edges of images may appear jagged while adjusting the image. · When correcting trapezoidal distortion, the aspect ratio of the image will change slightly .
Compresses lower side.
3
Press
.
· The on-screen display of the Keystone Correction mode will disappear.
-29
Image Projection
Adjusting the Lens
The image is focused and adjusted to the desired size using the focus ring or zoom knob on the projector. Zoom knob Focus ring
1
Adjust the focus by rotating the focus ring.
2
Adjust zooming by moving the zoom knob.
Zoo m in
Zoo
mo
ut
-30
Using the Adjustment Feet
The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector when the screen is not perpendicular to the lens centre of the projector, or when installation surface is slightly slanted. When the screen is in a higher position than the projector, the projection image can be made higher by adjusting the projector.
HEIGHT ADJUST button
1 2
Press the HEIGHT ADJUST button.
· The front adjustment foot comes out.
Lift the projector to adjust its height while pressing the HEIGHT ADJUST button.
· The projector is adjustable up to approximately 12 degrees (5 steps). · When lowering the projector, it may be difficult to move the front adjustment foot because the installation surface is difficult to slide. HEIGHT ADJUST button
Front adjustment foot
Basic Operation
3
Remove your hands from the HEIGHT ADJUST button of the projector after its height has been finely adjusted. Use the rear adjustment foot to make the projector level.
· The projector is adjustable ±1 degree from the standard position.
4
Note
· When the height of the image is being adjusted by the adjustment feet, the image becomes distorted trapezoidally. In this case, see "Correcting Trapezoidal Distortion" on page 29 to correct the trapezoidal distortion.
Info
· Do not press the HEIGHT ADJUST button when the front adjustment foot comes out without firmly holding the projector. · When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector.
Rear adjustment foot
-31
Image Projection
Variable Lens Shift Feature
In addition to the zoom function and adjustment of projection angle using the adjustment foot, it is possible to move the lens up and down and left and right (360°) to adjust the projection position simply by moving the lens shift lever on the front of the projector. This is a useful function in cases such as when the screen cannot be moved.
When moving upwards or downwards
When moving in the left and right direction
ge
Adjustable ran
Adjustable range
ge
Adjustable ran
Adjustable range
Lens shift lever Adjustable range of the lens shift lever
The adjustable range using the lens shift lever has limitations. The image can be adjusted as shown below.
Lens shift lever
Image centre locus
Zooming axis Adjustable range of the image centre
Image centre
Height of the projected image × (about) 60% Width of the projected image × (about) 30%
-32
Adjusting the Projected Image Position
Adjust the projected image position using the lens shift lever.
Info
· When using the projector (during projection), be sure not to subject the projector to any impact. If the projector is subjected to impact, the projection image may deviate from the adjusted position. · When transporting or carrying the projector, attach the lens shipping block and the lens cap to the projector. [. . . ] 47 OSD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Picture Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP XV-Z10E
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP XV-Z10E will begin.