User manual SHARP XV-Z30000 SETUP MANUAL

[. . . ] Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/ EEG. Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC come emendata dalla direttiva 93/68/EEC. Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela directiva 93/68/CEE. Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la 93/68/CEE. [. . . ] · A Macintosh adapter may be required for using the computer cable to connect to some Macintosh computers. Contact your nearest Sharp Authorised Projector Dealer or Service Centre. Computer Info · Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. · Do not connect or disconnect an RS-232C cable to or from the computer while it is on. This may damage your computer. -25 Image Projection Turning the Projector on Connect the required external equipment to the projector before carrying out the following procedures. Info · The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language according to the procedure on page 51. 1 2 Plug the power cord into the wall outlet. · The power indicator illuminates red, and the projector enters standby mode. Power indicator ON button INPUT button ON button Press on the projector or on the remote control. · The power indicator illuminates green. · When the lamp turns on, the lamp indicator illuminates green. After the lamp indicator illuminates green, the projector is ready to start operation. Lamp indicator Note · The lamp indicator illuminates, indicating the status of the lamp. · If the projector is put into the standby mode and immediately turned on again, the lamp indicator may take some time to illuminate. Info · See page 30 for details about adjusting the focus and the size of the projected image. · See "Using the Adjustment Feet" on page 31 for adjusting the projector angle and "Variable Lens Shift Feature" on page 32 for adjusting the projected image position. -26 Switching the INPUT Mode Select the appropriate input mode for the connected equipment. INPUT buttons Press , or on the remote control to select the INPUT mode. on the projector, input mode · When pressing switches in order of INPUT 1 INPUT 2 INPUT 3 . "On-screen Display of INPUT Mode (Example) INPUT 1 mode Using Component Note · When no signal is received, "NO SIGNAL" will be displayed. When a signal that the projector is not preset to receive is received, "NOT REG. " will be displayed. · The INPUT mode is not displayed when "OSD Display" of the "Options" menu is set to " (OFF). If the projector is subjected to impact, the projection image may deviate from the adjusted position. · When transporting or carrying the projector, attach the lens shipping block and the lens cap to the projector. · When the angle is being adjusted using the adjustment foot, deviation of the projected image arising when carrying out lens shift in the lateral direction cannot be corrected by the Keystone Correction. Basic Operation Freeze Image You can instantly freeze a moving image with the remote control. Freezing a Moving Image 1 2 Press . FREEZE button · The projected image is frozen. Press again to return to the moving image from the currently connected device. -33 Selecting the Picture Display Mode This function allows you to modify or customise the picture display mode to enhance the input image. Depending on the input signal, you can choose "STRETCH", "SIDE BAR" or "CINEMA ZOOM" image. Switching the Picture Display Using Different Input Signals Press · Pressing UNDO button RESIZE button . changes the picture display mode as shown on page 35. · To return to the standard image ("STRETCH"), press while "RESIZE" is displayed on the screen. · You can also change the picture display mode by pressing on the projector. RESIZE button UNDO button -34 Input Signal Output screen image STRETCH (Default setting) SIDE BAR CINEMA ZOOM 4:3 aspect ratio 480I 480P NTSC PAL SECAM Letter box Squeezed 1080I 16:9 aspect ratio 720P Basic Operation VGA SVGA XGA 4:3 aspect ratio : Cutout area on which images cannot be projected. Note · "STRETCH" is fixed when 720P or 1080I signals are entered. -35 Using the Menu Screen The menu screens allow you to adjust the image and various projector settings. (The menu items differ depending on the input mode. ) The menu can be operated with the projector or with the remote control. Menu Selections (Adjustments) ', ", \, | buttons ENTER button 1 Press Note . MENU button · The "Picture" menu screen for the selected input mode is displayed. ENTER button UNDO button MENU button ', ", \, | buttons -36 2 Press \ or | to select the menu screen (icon) you want to set. Menu icon Menu screen Picture Fine Sync Options Language PRJ Mode Select the icon. · The menu icon for the selected menu screen is highlighted. Note · The "Fine Sync" menu is not available for INPUT 2 or 3. · For items on the menus, see the tree charts on pages 40 and 41. 3 Press ' or " to select the item you want to adjust. · The selected item is highlighted. Select the item. Note · If you want to adjust the item while viewafing the projected image, press ter selecting the item. When pressing ' or ", the following item ("Bright" after "Contrast") will be displayed. to return to the previous Adjustments and Settings 4 Press \ or | to adjust the item selected. · The adjustment is stored. 5 Press . · The menu screen will disappear. Adjust the item or make the setting. -37 Using the Menu Screen Menu Selections (Settings) ', ", \, | buttons ENTER button 1 Press Note . MENU button · The "Picture" menu screen for the selected input mode is displayed. ENTER button UNDO button MENU button ', ", \, | buttons 2 Press \ or | to select the menu screen (icon) you want to set. · The menu icon for the selected menu screen is highlighted. Menu icon Menu screen Picture Fine Sync Options Language PRJ Mode Select the icon. Note · The "Fine Sync" menu is not available for INPUT 2 or 3. · For items on the menus, see the tree charts on pages 40 and 41. -38 3 Press ' or " to select the item you want to set. Note · Press or \ to return to the previous screen. Select the item. 4 Press |. · The cursor shifts to the sub menu. [. . . ] 50 Menu Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 MUTE button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 ON button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]