User manual SHARP XLHP600 OPERATION MANUAL

[. . . ] MICRO COMPONENT SYSTEM MODEL Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. XL-HP600E Micro Component System consisting of XL-HP600E (main unit) and CP-HP600E (speaker system). XL-HP600E OPERATION MANUAL If you require any advice or assistance regarding your Sharp product, please visit our web-site www. sharp. co. uk/customersupport. Customers without Internet access may telephone 08705 274277 during office hours (or (01) 676 0648 if telephoning from Ireland). 0301 XLHP600E_FRONT. pm 1 03. 2. 3, 5:42 PM XL-HP600E Special notes NOTES FOR USERS IN THE U. K. [. . . ] Random play The tracks on the disc(s) can be played in random order automatically. To random play all tracks on the chosen disc: 1 Press one of the DISC SELECT - ( 1 - 3) buttons. Notes: button during random play, you can move to " If you press the the track selected next by the random operation. On the other hand, the button does not allow you to move to the previous track. " In random play, the CD player will select and play tracks automatically. (You cannot select the order of the tracks. ) Caution: After performing repeat or random play, be sure to press the (CD ) button. Otherwise, the disc(s) will play continuously. 16 03/1/31 XL-HP600E(E)2. fm XL-HP600E !Programmed play You can choose up to 32 selections for playback in the order you like. 1 Whilst in the stop mode, press the MEMORY/SET (MEMORY) button to enter the programming save mode. 2 3 Press the direct search buttons on the remote control to select the desired track. Selected track number You can also select a track by pressing the or button. !Care of compact discs Compact discs are fairly resistant to damage, however mistracking can occur due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your CD collection and player. " Do not write on either side of the disc, particularly the non-label side from which signals are read. " Keep your discs away from direct sunlight, heat, and excessive moisture. Fingerprints, dirt, or water on the CDs can cause noise or mistracking. If a CD is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the centre, along the radius. NO YES Correct 4 5 Press the MEMORY/SET (MEMORY) button to save the track number. If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR button. The total number of memory will appear. 6 7 Press the / button to start playback. ( 13) During programme play, the DISC SELECT buttons will not work. 17 03/1/31 XL-HP600E(E)2. fm CD Playback Press one of the DISC SELECT ( 1 - 3) buttons to select the desired disc. Selected disc number To clear the programmed selections: Press the CLEAR button on the remote control whilst the "MEMORY" indicator is flashing. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. To cancel the programmed play mode: Whilst in the stop mode and the "MEMORY" indicator is lit, press the CLEAR button on the remote control. The "MEMORY" indicator will disappear and all the programmed contents will be cleared. Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. [. . . ] Amplifier Output power Output terminals RMS: 150 W (75 W + 75 W) (10 % T. H. D. ) RMS: 126 W (63 W + 63 W) (0. 9 % T. H. D. ) Speakers: 6 ohms Headphones: 16 - 50 ohms (recommended: 32 ohms) Subwoofer (audio signal): 200 mV/10 k ohms at 70 Hz Video/Auxiliary (audio signal): 500 mV/47 k ohms !Cleaning the CD pickup lens Poor performance during CD playback (skipping or jumping) can be caused by a dirty or contaminated CD laser pick up lens. If this happens then the use of a commercially available CD lens cleaning discs may restore normal operation. Contact your supplier or local CD software dealer to obtain CD lens cleaning discs. [. . . ]