User manual SHARP XL-HF401PH QUICK GUIDE

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. [. . . ] On the other hand, the button does not allow you to move to the previous track. " In random play, the CD player will select and play tracks automatically. (You cannot select the order of the tracks. ) Caution: After performing repeat or random play, be sure to press the ) button. (CD 19 CD Playback XL-HF401PH Advanced CD Playback (continued) !Programmed play You can choose up to 32 selections for playback in the order you like. 1 While in the stop mode, press the MEMORY/SET (MEMORY) button to enter the programming save mode. To clear the programmed selections: Press the CLEAR/DIMMER button on the remote control while the "MEMORY" indicator is flashing. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. To cancel the programmed play mode: While in the stop mode and the "MEMORY" indicator is lit, press the CLEAR/DIMMER button on the remote control. The "MEMORY" indicator will disappear and all the programmed contents will be cleared. Adding tracks to the program: If a program has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original program. To check which tracks are programmed: While the unit is stopped in the programmed play mode, press the or button. The preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each. Press the PRESET ( or ) button again when the desired station is located. 3 Radio Within 30 seconds, press the PRESET ( or ) button to select the preset channel number. Store the stations in memory, in order, starting with preset channel 1. Within 30 seconds, press the MEMORY/SET (MEMORY) button to store that station in memory. 4 If the "MEMORY" and preset number indicators go out before the station is memorized, repeat the operation from step 2. 5 Repeat steps 1 - 4 to set other stations, or to change a preset station. When a new station is stored in memory, the station previously memorized will be erased. !To erase entire preset memory 1 2 Press the ON/STAND-BY button to enter the stand-by mode. While pressing down the button and the X-BASS/DEMO button, press the CLOCK/TIMER button until "TUNER CL" appears. Note: The backup function protects the memorized stations for a few hours should there be a power failure or the AC power cord disconnection. 22 Listening to a cassette tape Before playback: " For playback, use normal or low-noise tapes for the best sound. (Metal or CrO tapes are not recommended. ) " Do not use C-120 tapes or poor-quality tapes, as they may cause malfunctions. " Before loading a tape into the cassette compartment, tighten the slack with a pen or a pencil. XL-HF401PH !Tape playback 1 2 3 Press the ON/STAND-BY button to turn the power on. Open the cassette door by pushing the area marked " PUSH EJECT". 4 Load a cassette into the cassette compartment with side A facing you. 5 Press the button to choose one side or both sides. [. . . ] Contact your local CD software dealer for options. NO YES Correct !Cleaning the cabinet Periodically wipe the cabinet with a soft cloth and a diluted soap solution, then with a dry cloth. Caution: " Do not use chemicals for cleaning (gasoline, paint thinner, etc. ). It may cause malfunctions. 34 Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. [. . . ]