User manual SHARP XL-60H/70H

[. . . ] MODEL MICRO COMPONENT SYSTEM OPERATION MANUAL XL-60H XL-70H Thank you for purchasing this SHARP product. To obtain the best performance from this product please read this manual carefully. It will guide you in operating your SHARP product. XL-60H/XL-70H Micro Component System consisting of XL-60H/XL-70H (main unit) and CP-XL60H/ CP-XL70H (speaker system). XL-60H XL-70H 60H/70H(SUK). FRONT 1 00. 1. 7, 5:07 PM SPECIAL NOTES NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a nonrewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug must be used. [. . . ] Notes: q When radio interference occurs during auto scan tuning, auto scan tuning may stop automatically at that point. q If a weak station signal is found during auto scan tuning, the station will be skipped. q When an RDS (Radio Data System) station is tuned in, the frequency will be displayed first and then the RDS indicator will light. Finally, the station name will appear. 4 Within 5 seconds, press the MEMORY/SET 5 Repeat steps 1 - 4 to set other preset stations, or to change a preset station. After use: Press the ON/STAND-BY button to enter the standby mode. 5 To receive an FM stereo transmission, press the BAND button so that the "ST" indicator on the display lights up. Note: q The last station tuned in will be recalled, even after changing the tuning band or the function, or after switching the unit to the stand-by mode. 6 If the FM reception is weak, press the BAND 17 60H/70H(SUK)13-17 17 00. 1. 5, 11:40 AM (Continued) To recall a memorised station: To clear a memorised station: 2 1 PRESET ( ) 3 4 2 1 1 Press the VOLUME/JOG button. 2 Turn the jog dial to select the preset channel number you want to erase. 3 Press the MEMORY/SET button. 4 Within 5 seconds, press the TUN CLEAR button. (Main unit operation) s Preset memory scan The stations saved in the preset memory can be scanned automatically. 1 Press the VOLUME/JOG button. q The preset channel number will flash. turn the jog dial to select the desired station. 2 Whilst the preset channel number is flashing, (Remote control operation) Press the PRESET ( or ) button for less than 0. 5 seconds to select the desired station. q The stations (preset channel number, frequency and frequency band) which have been stored in memory will appear in the display in numerical order, irrespective of the frequency bands. Note: When searching for a memorised station, do not press the PRESET button for more than 0. 5 seconds. When the PRESET button is pressed for more than 0. 5 seconds, the unit will enter the preset memory scan mode. 1, 2 1 To scan the preset stations, press the PRESET ( or ) button for more than 0. 5 seconds. q The station preset number flashes and programmed stations are sequentially received for 5 seconds each. 2 Press the PRESET ( or ) button again to stop the memory scan at the desired station. Note: When the preset memory does not have any stations stored in it, the preset memory scan will not function. Backup function: The backup function protects all station presets for a few hours should there be a power failure or the AC power lead is removed from the AC socket. 18 60H/70H(SUK)18-22 18 00. 1. 5, 11:40 AM RDS (Radio Data System) OPERATION RDS is a broadcasting service which a growing number of FM stations are now providing. It allows these FM stations to send additional signals along with their regular programme signals. For example, the stations send their station names, and information about what type of programme they broadcast, such as sports or music, etc. When tuned to an FM station providing the RDS service, RDS will appear, the station frequency (and then the station name if sent) will be displayed. The TP (Traffic Programme) will appear on the display when the received broadcast carries traffic announcements, and the TA (Traffic Announcement) will appear whilst a traffic announcement is being received. EON will appear whilst the EON (Enhanced Other Networks information) data is being broadcast. Note: When the TP and TA appear at the same time, an announcement is being made. (See page 26. ) Descriptions of the PTY (Programme Type) codes, TP (Traffic Programme) and TA (Traffic Announcement) With the XL-60H/XL-70H, you can search for and receive the following PTY, TP and TA signals. NEWS: Short accounts of facts, events and publicly expressed views, reportage and actuality. [. . . ] Adjust the VOLUME control for desired volume. To headphones socket RESETTING THE MICROCOMPUTER 1 3 3 Reset the microcomputer under the following conditions: q To erase all of the stored memory contents (clock and timer settings, and tuner and CD presets). q If the operation is not correct. 1 Press the ON/STAND-BY button to enter the stand-by mode. 2 Unplug the AC power lead from the AC INPUT socket on this unit. AC INPUT 3 Whilst pressing down the MEMORY/SET button and the 0 button, plug the AC power lead into the AC INPUT socket on this unit. Caution: q The operation explained above will erase all data stored in memory, such as clock and timer settings, and tuner and CD presets. 2, 3 MAINTENANCE q After long use, the deck's heads and capstan may become magnetised, causing poor sound. Demagnetise these parts once every 30 hours of playing/recording time by using a commercial tape head demagnetiser. [. . . ]