User manual SHARP XG-SV100W

[. . . ] DATA PROJECTOR MODEL XG-SV100W XG-SV200X SETUP MANUAL Connecting Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 RS-232C Specifications and Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Operating the Projector Using the PJLinkTM Protocol . . . . . . . . . . . . . . . . . . 10 Setting up the Projector Network Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2 Set temporarily as follows: IP address: 192. 168. 150. 3 Subnet mask: 255. 255. 255. 0 Default gateway: (Do not input any values. ) Note · The factory default settings for the projector are as follows: DHCP Client: OFF IP address: 192. 168. 150. 2 Subnet mask: 255. 255. 255. 0 Default gateway: 0. 0. 0. 0 7 After setting, click the "OK" button, and then restart the computer. After confirming or setting, proceed to "3. Setting up Network Connection for the Projector". -14 Setting up the Projector Network Environment 3. Setting up a Network Connection for the Projector Settings for such items as the projector's IP address and subnet mask are compatible with the existing network. (See page 62 of the projector's operation manual for setting. ) DHCP Client: Off IP Address: 192. 168. 150. 002 Subnet Mask: 255. 255. 255. 000 1 Start Internet Explorer (version 6. 0 or later) on the computer, and enter "http://192. 168. 150. 2/" in "Address", and then press the "Enter" key. If a user name and a password have not yet been set, just click the "OK" button. · If a user name and a password have been set, input the user name and the password, and click the "OK" button. · If the user name or password is entered incorrectly three times, an error message will be displayed. · When you are using Internet Explorer 7 or later, other setup screen may be displayed. In this case, make the proper adjustments for the setup screen. 2 3 When the screen as shown on the right appears, click "TCP/IP". -15 Setting up the Projector Network Environment 4 The TCP/IP setting screen appears, ready for network settings for the projector. Items Setting example / Remarks New You can set the password to protect Password the TCP/IP setting. DHCP Client IP Address Select "ON" or "OFF" to determine whether to use DHCP Client. You can set this item when "DHCP Client" is set to "OFF". Factory default setting: 192. 168. 150. 2 Enter an IP address appropriate for the network. You can set this item when "DHCP Client" is set to "OFF". Factory default setting: 255. 255. 255. 0 Set the subnet mask to the same as that of the computer and equipment on the network. You can set this item when "DHCP Client" is set to "OFF". Factory default setting: 0. 0. 0. 0 * When not in use, set to "0. 0. 0. 0". Factory default setting: 0. 0. 0. 0 * When not in use, set to "0. 0. 0. 0". Subnet Mask Default Gateway DNS Server Note · Confirm the existing network's segment (IP address group) to avoid setting an IP address that duplicates the IP addresses of other network equipment or computers. If "192. 168. 150. 2" is not used in the network having an IP address of "192. 168. 150. XXX", you don't have to change the projector IP address. · For details about each setting, consult your network administrator. 5 6 Click the "Apply" button. The set values appear. Confirm that the values are set properly, and then click the "Confirm" button. · · · · Close the browser. Change the IP address of the setting computer back to its original address, which you have noted down in Step 6-1 on page 14, and then connect the computer and the projector to the network. -16 Controlling the Projector via LAN After connecting the projector to your network, enter the projector IP address in "Address" on Internet Explorer (version 6. 0 or later) using a computer on the network to start a setup screen that will enable control of the projector via the network. Controlling the Projector Using Internet Explorer Complete connections to external equipment before starting the operation. (See pages 22-26 of the projector's operation manual. ) Complete the AC cord connection. (See page 26 of the projector's operation manual. ) Note · When connecting the projector to the LAN, use a commercially available LAN cable (UTP cable, Category 5, cross-over type). [. . . ] (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". · Gateway When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnets for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. (Example) When the IP address is "192. 168. 150. 2" and the subnet mask is "255. 255. 255. 0" for the projector, the IP address for the computer should be "192. 168. 150. X" (X=3-254) and the subnet mask should be "255. 255. 255. 0". Note · When "DHCP Client" is set to "Off" on the projector: IP address: 192. 168. 150. 2 Subnet mask: 255. 255. 255. 0 Gateway address: 0. 0. 0. 0 (Not Used) · For network settings for the projector, refer to page 15. -24 Troubleshooting Take the following steps for checking the network settings for the computer. [. . . ]