User manual SHARP WQ-T484H

[. . . ] 32 Connecting Pin Assignments COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals: mini D-sub 15 pin female connector 11 15 COMPUTER Input/Output Pin No. Not connected 1 6 5 10 DVI-I Terminal: 29 pin connector 23 24 C3 C5 C4 C2 C1 87 16 21 9 18 17 · DVI Digital Input Pin No. Signal Hot plug detection T. M. D. S data 0­ T. M. D. S data 0+ T. M. D. S data 0 shield Not connected Not connected T. M. D. S clock shield T. M. D. S clock+ T. M. D. S clock­ Not connected Not connected Not connected Not connected Ground · DVI Analog RGB Input Pin No. Signal Not connected Not connected Not connected Not connected Not connected DDC clock DDC data Vertical sync Not connected Not connected Not connected Not connected Not connected +5V power Ground Pin No. [. . . ] Setting the TCP port number used when exchanging data with the projector (from 1025 to 65535). Setting the port number used when searching for the projector (from 1025 to 65535). On this screen, you can make settings for sending e-mail to report when the projector has generated an error. Items SMTP Server Setting example / Remarks Setting an SMTP server address for email transmission. e. g. 1: 192. 168. 150. 253 e. g. 2: smtp123. sharp. co. jp * When using a domain name, make settings for the DNS server. The name set here appears in the "Originator Name" column of the body of the message. Originator Email Address Originator Name Data Port Search Port After clicking the "Apply" button, the set values appear. Confirm that the values are set properly, and then click the "Confirm" button. Note · After setting items, wait for about 15 seconds and then re-access. · You can input the characters below: A-Z, 0-9, -, _, (, ), space (When "a-z" are input, they are converted to "A-Z" automatically. ) Note · SMTP Server, Originator E-mail Address and Originator Name can be up to 64 characters. · You can input the characters below: SMTP Server and Originator E-mail Address: a-z, A-Z, 0-9, !, #, $, %, &, *, +, -, /, =, ?, ^, {, |, }, ~, _, ', . , @, ` (You can input "@" only one time for "Originator E-mail Address". ) Originator Name : a-z, A-Z, 0-9, -, _, (, ), space · If the settings of "3. Setting up a Network Connection for the Projector" on pages 13 and 14 are incorrectly set, e-mail will not be sent. -18 Controlling the Projector via LAN Setting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail ­ Recipient Settings) Setting Error Items and the URL that are to be Displayed when an Error Occurs (Service & Support ­ Access URL) On this screen, you can input e-mail destinations to which error notification (error items) e-mails are sent. Items E-mail Address Description Set addresses to which error notification e-mail is sent. You can set up to five addresses. On this screen, you can make settings of the URL and error items that are to be displayed when the projector has generated an error. Items Access URL Description Set the URL that is to be displayed when an error occurs. The URL is displayed when an error checked in their check boxes occurs. Error e-mail is sent on the error items Error Mail (Lamp, Temp, checked in their check boxes. This allows you to confirm that the settings for e-mail transmission are properly set. Condition (Always, Lamp, Temp, Fan, Cover) Test The set URL site is test-displayed. (Page 29) [!] Restore Default Setting Restores all setting values that can be set using the menu to the default state. (Page 29) Note · When "DHCP Client" is set to "OFF" on the projector: IP address: 192. 168. 150. 2 Subnet mask: 255. 255. 255. 0 Default gateway: 0. 0. 0. 0 -22 Setting up the Projector Using RS-232C or Telnet Enter number or symbol of item to be selected on the SETUP MENU. Setting is carried out one item at a time, and saved at the end. View Setting Detail List ([V]View All Setting) SETUP MENU -----------------------------SETUP MENU---------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>v Model Name : XX-XXXX Projector Name : XX-XXXX MAC Address : XX:XX:XX:XX:XX:XX DHCP Client : Disable IP Address : 192. 168. 150. 2 Subnet Mask : 255. 255. 255. 0 Default Gateway : Not Used RS-232 Baud Rate : 9600 bps Password : Not Required **********(Advanced Status)********** Data Port : 10002 Accept IP Address : Accept All Auto Logout Time : 5 minutes Search Port : 5006 Set Items Example: When setting IP Address (change from 192. 168. 150. 2 to 192. 168. 150. 3) SETUP MENU -----------------------------SETUP MENU---------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>1 IP Address : 192. 168. 150. 2 Please Enter : 192. 168. 150. 3 --> 192. 168. 150. 3 (change) -----------------------------SETUP MENU---------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>v Model Name : XX-XXXX Projector Name : XX-XXXX MAC Address : XX:XX:XX:XX:XX:XX DHCP Client : Disable IP Address : 192. 168. 150. 3 Subnet Mask : 255. 255. 255. 0 Default Gateway : Not Used RS-232C Baud Rate : 9600 bps Password : Not Required **********(Advanced Status)********** Data Port : 10002 Accept IP Address : Accept All Auto Logout Time : 5 minutes Search Port : 5006 1 1 2 *1 *2 * 3 1 Enter "v" and press the "Enter" key. Display all setting values(*). *3 1 Enter "1" (number of item to be set), and press the "Enter" key. 3 Enter "v" and press the "Enter" key to verify setting detail list. IP address is being changed (*3). Note · Verification of setting detail list can be omitted. · Setting details are not effective until they have been saved. (Page 24) · If an invalid number is entered, an error message ("Parameter Error!") will be displayed. -23 Setting up the Projector Using RS-232C or Telnet Save Settings and Quit ([S]Save & Quit) Save set values and quit menu. SETUP MENU ----------------------------SETUP MENU--------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged setup>s All Connection will be disconnect. y Apply New setting. . . Done. Quit without Saving Settings ([Q]Quit Unchanged) Quit menu without saving setting values. SETUP MENU ----------------------------SETUP MENU--------------------------[1]IP Address [2]Subnet Mask [3]Default Gateway [4]User Name [5]Password [6]RS-232C Baud Rate [7]Projector Name [8]DHCP Client [A]Advanced Setup [D]Disconnect All [V]View All Setting [S]Save & Quit [Q]Quit Unchanged 1 2 setup>q Quit Without Saving(y/n)? [. . . ] \ Check that the power supply is turned on for the network device such as a hub between the projector and a computer. Check the network settings for the computer and the projector \ Check the following network settings for the projector. · IP Address Check that the IP address for the projector is not duplicated on the network. · Subnet Mask When the gateway setting for the projector is "0. 0. 0. 0" (Not Used), or the gateway setting for the projector and the default gateway setting for the computer are the same: · The subnet masks for the projector and the computer should be the same. · The IP address parts shown by the subnet mask for the projector and the computer should be the same. [. . . ]