User manual SHARP VCMH814 OPERATION MANUAL

[. . . ] TINS-3993UMZZ HM Final Cov copy 11/5/01 2:24 pm Page 1 VC-MH814HM VC-MH814LM VIDEO CASSETTE RECORDER OPERATION MANUAL G S-VHS SIMPLE PLAYBACK G NTSC SIMPLE PLAYBACK G AUTO INSTALLATION G SHARP SUPER PICTURE G NICAM Hi-Fi STEREO G 6 HEAD EXTENDED PLAY G CHILD LOCK TINS-3993UMZZ HM Final Cov copy 11/5/01 2:24 pm Page 2 Dear SHARP Customer Thank you for buying this SHARP VCR. Given proper care it will provide years of entertainment for the whole family. Please read this operation manual carefully before attempting to operate the VCR. Copyright G Audio-visual material may consist of copyrighted works which must not be recorded without the authority of the owner of the copyright. [. . . ] If you wish to change the RECORDING SPEED, use the [ Press[ required. / 9. 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 2 2 : 3 0 --/-- --:--:---/-- --:--:-SP LP --- / ]to highlight SP. ]to select standard play (SP), long play (LP) or extended play (EP) as 10. Press the SET · SET button to confirm. The MENU now shows all the timer settings you have entered. If you wish to make additional timer recordings, repeat this procedure. 11. When you have completed entering timer settings, press the MENU button to remove the menu from the TV screen. 12. Ensure that the tape on which you wish to record is inserted into the VCR, then press the TIMER ON/OFF button once to place the VCR in TIMER STANDBY mode. will be shown on the display and the timer standby indicator will be illuminated. NOTES: · · · If the symbol and the red indicator light flashes a video tape has not been inserted into the VCR. If the video tape is ejected when the VCR tries to record the record protection tab has been removed. If there are further recordings to be made, the VCR will return to Timer Standby. 16 TINS-3993UMZZ. book Page 17 Monday, June 4, 2001 11:24 AM BASIC OPERATION HOW TO CHECK, CHANGE AND CANCEL A DELAYED RECORDING Before you start! · If the Timer Standby symbol appears on the VCR display symbol. and the red timer standby indicator is illuminated, press the TIMER ON/OFF button to remove the CHECKING A RECORDING 1. button. MENU SCREEN T I ME R MOD E SE T UP / ]to select TIMER. Press the button to confirm. 4. · All the delayed recordings in the VCR's memory will be shown. If you wish to change or cancel any settings, follow the procedures below. SET : SE L ECT : ENT ER ME NU : E X I T CHANGING A RECORDING 1. To change a delayed recording, press [ / ] to highlight the recording, then press SET the SET button to select. 1/2 3. Press[ / ]to highlight the setting to be / ] changed and correct it by using the[ or the NUMBER BUTTONS. DA T E 21 / 06 --/---/---/-- P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-- SP ---- 4. When all corrections are complete press the SET button to confirm, then press the MENU button to exit. To cancel a delayed recording, press [ / ]to highlight the recording to be button to exit. Press the MENU NOTE: · 1/2 DA T E P R S T AR T S T OP 2 1 / 0 6 0 2 1 2 : 0 0 1 3 : 0 0 SP --/-- --:--:-- ---/-- --:--:-- ---/-- --:--:-- -- If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to Timer Standby mode. 17 TINS-3993UMZZ. book Page 18 Friday, May 11, 2001 12:37 PM ADVANCED OPERATION AUDIO AND YOUR VCR HI-FI STEREO SOUND Stereo sound is possible from this VCR if you have a stereo TV connected to the VCR with a scart lead, or audio equipment connected with audio phono leads. The sound output from the VCR is controlled by the AUDIO OUT button on the remote control. If you wish to change the sound output you can use the AUDIO OUT button as follows: · button once. The LEFT audio channel will be sent to BOTH Press the AUDIO OUT speakers. Press the AUDIO OUT button a third time and the MONO track will be sent to BOTH speakers. [. . . ] Press and hold MENU and CHANNEL DOWN front of the VCR for 10 seconds. VCR RESET IS NOW COMPLETE Please continue with your previous procedure. RF CHANNEL TUNING If you have a preferred RF output channel this can be set manually between channels 21 and 69 by following the procedure below. 1. The channel number can now be changed by using the VCR CHANNEL buttons. (White text blue background) V CR R F SET : ENT ER ME NU : E X I T RF THROUGH ON/OFF: If you wish to connect your VCR to the TV with only a scart lead, the RF Output on your VCR can be turned OFF and ON. To do this press the CLEAR then SET SET buttons on the remote control at point 3 from RF CHANNEL TUNING above. [. . . ]