User manual SHARP VC-M35SM/M351SM/M350SM

[. . . ] CONTENTS BEFORE USING YOUR VCR Important notes on your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpacking the accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLING YOUR VCR Connecting the cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Tuning the TV into the VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Then press SET to confirm. GB-12 Module 07C. fm Page 13 Thursday, April 20, 2000 10:18 AM BASIC OPERATION HOW TO SET A DELAYED RECORDING 8. Enter the start time using the [ / ] or the 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 -:---/-- --:--:---/-- --:--:-- NUMBER BUTTONS hours first then minutes (when entering less than 10 minutes add a '0' before the number), for example for 21:05 start, press 2 1 0 5. Enter the stop time, for example for 22:30 stop, press 2 2 3 0. 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 9 / 0 7D0 3 2 1 : 0 5 2 2 : 3 0 --/-- --:-- --:---/-- --:-- --:-- 10. Press SET to confirm. · The MENU now shows all the timer settings you have entered. If you wish to make additional timer recordings, repeat this procedure. 11. When you have completed entering timer settings, press MENU to remove the menu from the TV screen. 12. Press TIMER ON/OFF once to place the VCR in TIMER POWERSAVE OR TIMER STANDBY mode. will be shown on the display. NOTES: · · · If flashes a video tape has not been inserted into the VCR. If the video tape is ejected when the VCR tries to record the record protection tab has been removed. If there are further recordings to be made, the VCR will return to TIMER POWERSAVE OR TIMER STANDBY. GB-13 TINS-3799UMZZ ENGLISH. book Page 14 Thursday, April 20, 2000 9:23 AM BASIC OPERATION HOW TO SET A DELAYED RECORDING CHECKING, CHANGING AND CANCELLING A RECORDING CHECKING A RECORDING MENU SCREEN T I ME R MOD E SE T UP 1. If in TIMER POWERSAVE/TIMER STANDBY mode, press TIMER ON/OFF to exit. 2. · · All the delayed recordings in the VCR's memory will be shown. Press SET to SET : SE L ECT : ENT ER ME NU : E X I T CHANGING A RECORDING 1. Follow steps 1 to 4 of CHECKING A RECORDING. 1/2 DA T E 21 / 06 --/---/---/-P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:-- 2. If you wish to change a delayed recording, press [ / ] to highlight the recording, then press SET. 3. Press [ / ] to highlight the setting to be changed and correct it by using the[ / or the NUMBER BUTTONS. When all corrections are complete press SET, CANCELLING A RECORDING 1. Follow steps 1 to 4 of CHECKING A RECORDING. 1/2 DA T E P R S T AR T S T OP 21 / 06 02 12 : 00 13 : 00 --/-- --:--:---/-- --:--:---/-- --:--:-- 2. If you wish to cancel a delayed recording, press [ / ] to highlight the recording to be cancelled, then press CLEAR. 3. Press MENU. NOTE: · If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to TIMER POWERSAVE OR TIMER STANDBY mode. GB-14 TINS-3799UMZZ ENGLISH. book Page 15 Thursday, April 20, 2000 9:23 AM ADVANCED OPERATION PLAYBACK OF A VIDEO TAPE CHECKING THE AMOUNT OF TAPE REMAINING When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. [. . . ] The display can be selected by pressing the MODE OSD button on the remote control, 1, 2, 3 or 4 times. 1. AUTO, the current mode and channel number will be displayed for 3 seconds when an operation or number button is pressed. 1. I 1 CH 5 9 2. FULL. , all the active features will also be shown on screen. 2. Programme number and channel Tape Status I SUPER P . 1 CH 5 9 ON Tape remaining Time Date Tape counter 22 : 00 9 / 07 00 R EM 1 : 0 5 0 : 00 . COUNTER, this display will show the tape counter and amount of tape remaining. 3. 4. [. . . ]