User manual SHARP UX-BD80/BD90

[. . . ] Troubleshooting IMPORTANT PLEASE KEEP THE EXTERNAL & INTERNAL PACKAGING SAFE. PLEASE DO NOT THROW IT AWAY. IN THE UNLIKELY EVENT OF A HARDWARE FAILURE, OUR REPAIR CENTRE WILL ASK YOU TO PUT YOUR SHARP FACSIMILE IN THIS BOX. THANK YOU FOR YOUR ASSISTANCE. MAINS PLUG WIRING INSTRUCTIONS This equipment is fitted with a moulded type mains plug which incorporates a detachable fuse cover, under no circumstances should the plug be used without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type observing the wiring code below. DANGER: The fuse from the cut-off plug should be removed and the plug should be disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted into a socket outlet as a serious electric shock may occur. [. . . ] This lets you hear your messages immediately after they come in, even when you are at a remote location. To use the Transfer function, you must first program the number that you wish the machine to call (the transfer number), and record the transfer message that plays when you answer the phone at the remote location. When you return and no longer wish to use the transfer function, turn it off. Programming the transfer number To use the Transfer function, you must first program the number to call (the transfer number). 1 2 3 Press once and once. Display: A. M. SETTING Press once and 3 times. TRANSFER TEL # Press . ENTER TEL # 93 4. Answering Machine Transfer Function 4 Press the number keys to enter the transfer number. · To insert a pause between any two digits of the number, press . 5 6 Press START/ MEMORY . TRANSFER FUNC Press to return to the date and time display. Recording the transfer message The transfer message plays when you answer the telephone, and informs you that the call is a transfer call. Enter your remote code number now. " Note: Make sure that no other cordless handsets are in use when recording the message (the conversation on the cordless handset may also be recorded). 1 2 3 4 Press REC/MEMO once and twice. Display: 01-JAN 10:30 OGM2 (TRANSFER) Press once. Pick up the cordless handset and press . Speak into the cordless handset to record the message. · The transfer message can be up to 15 seconds long. While recording, the display will show the time left to record. 94 Transfer Function 5 When finished, press machine. on the cordless handset or on the Checking or erasing the transfer message To check or erase the transfer message, follow Steps 1 and 2 of the above procedure, and then press erase the message. PLAY/HOLD to check the message, or DELETE to Turning the Transfer function on and off When you go out and wish to use the Transfer function, turn it on as follows: 1 2 3 4 Press once and once. Display: A. M. SETTING Press once and 3 times. TRANSFER FUNC Press once. TRANSFER FUNC 1=YES, 2=NO The display briefly shows your selection, then: Press function. (Press to turn on the Transfer ON A. M. FAILURE to turn the function off. ) 5 Press to return to the date and time display. 95 4. Answering Machine Transfer Function 6 Each time the machine receives an incoming message, it will call your programmed transfer number. When you answer, you will hear your recorded message telling you that the call is a transfer call. On the dial pad of your phone, enter and , your remote code number (see page 97), . The machine will play back your messages. · You can also perform any of the remote operations described in Remote Operations later in this chapter (see page 97). Note: When you hang up after a transfer call, the machine will not immediately resume normal operation. If you want the machine to accept calls immediately after a transfer call, enter twice before hanging up (if you and to stop want to hang up during message playback, first enter playback, then enter twice). 96 Remote Operations Remote Operations When you are out, you can call the machine from any tone dial telephone and play back your messages using the remote commands. You can also use these commands to change the reception mode and other settings. Remote code number To access the machine to perform remote operations, you must first enter your remote code number. The remote code number has been set to "001" at the factory. If you wish to use a different number, follow these steps: 1 2 3 4 5 Press once and once. Display: A. M. SETTING Press once and twice. REMOTE CODE Press . REMOTE CODE= SELECT 3 DIGITS Press the number keys to enter a 3-digit remote code number. Press START/ MEMORY to store the remote number, and then to return to the date and time display. 97 4. Answering Machine Remote Operations Toll Saver When you call the machine to listen to your messages, it will answer after two rings if it has received at least one message, or after four rings if it has not received any messages. This allows you to save money on telephone charges, particularly if you are calling long distance. If the machine does not answer after two rings, you can simply hang up before it answers, saving yourself the cost of that call. If you do not want to use the Toll Saver function, you can turn it off by following the steps below. [. . . ] SET socket, 29 TEL/FAX reception mode, 37, 125 Telephone line cord, 29 Telephone Number List, 145 Time, setting, 35-36 Toll Saver function, 88, 98 Transaction Report, 146 Setting print condition, 147 Transfer Function, 93 Transferring calls, 57 176 REMOTE OPERATION CARD The card below is provided as a quick guide to remote operation. Cut it out and carry it with you when you go out. Remote Operation Guide 1. Call your fax from a touch-tone telephone, and press # when the outgoing message begins. After listening to your messages, you can either hang up to save them, or enter one of the commands on the reverse side. [. . . ]