User manual SHARP UX-108/178/188

[. . . ] Troubleshooting WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] This lets you know immediately who is calling without having to look at the display. To use this function, enter the desired phone number by following the steps below (only one phone number can be entered). 1 Press the keys shown at right. PRIORITY CALL # will appear in the display. FUNCTION 3 51 7. Special Functions Caller ID 2 3 Press 1 to enter a number, or 2 to clear a number. (If you pressed 2, go to Step 4. ) Enter the phone number, including the area code, by pressing the number keys (the number must be 10 digits long). Press the START key and then the STOP key. 1 or 2 5 4 5 5 5 5 1 5 2 3 (Example) 4 START STOP Blocking voice calls With Caller ID turned on, you can use the Anti Junk Fax function described in "Blocking Reception of Unwanted Faxes" in this chapter to block voice calls as well as fax receptions (the Anti Junk Fax function normally only blocks faxes). In this case, when a voice call or a fax transmission comes in from a number you have specified as a "Junk Number", your fax will break the connection as soon as it receives the calling phone number from the caller ID service (before the second ring). To use this function, set Option Setting 13 to YES as described in Chapter 8, "Optional Settings", and then enter the number in the Anti Junk Number List as described in "Blocking Reception of Unwanted Faxes". Note: This function cannot be used if you are using the Distinctive Ring function. 52 Distinctive Ring Distinctive Ring Important: · To use distinctive ring, you must subscribe to a distinctive ring service from your local phone company. Do not turn on this function if you do not subscribe to a distinctive ring service. · Your fax may not be compatible with some distinctive ring services. Distinctive ring is a service offered by some local telephone companies whereby they assign another number to your regular single line. If you subscribe to a distinctive ring service, you can set the fax machine to automatically answer when your second number is called. To have your fax automatically answer when your second number is called, follow the steps below: 1 Press these keys: FUNCTION 4 OPTION SETTING The display will show: 2 Press these keys: The display will show: DISTINCTIVE RING 7. Special Functions 53 Distinctive Ring 3 Press a number from 1 to 3 to select the ring pattern below that matches your second number's ring pattern. Or, press 4 to have your fax automatically answer your normal telephone number. Press 5 to turn off the distinctive ring function. 1 2 3 4 5 RING PATTERN 1: RING PATTERN 2: RING PATTERN 3: Two short rings. Two short rings and one long ring. STANDARD RING: Your standard (normal) ring pattern. OFF SETTING: Turn distinctive ring off. The display will show: FAX SIGNAL RX 4 Press the STOP key. STOP 5 Set the reception mode to FAX. RECEPTION MODE TEL FAX A. M. When using distinctive ring, you must set the reception mode of your fax to FAX. When your designated fax number is dialed, your fax will automatically answer and begin reception after two rings. Note that other devices on the same line will also ring until your fax answers. If one of your other numbers is dialed, the fax will ring; however, it will not answer. Note: If you are using an answering machine with your distinctive ring service, the answering machine must be connected to a separate wall jack. 54 Blocking Reception of Unwanted Faxes Blocking Reception of Unwanted Faxes The Anti Junk Fax function allows you to block reception of faxes from parties which you specify. [. . . ] Press: START 3 FAX/TEL # MODE Display shows: RECEIVING DOCUMENTS TEL FAX 2. Enter a 2-digit Speed Dial number (from 01 to 10 for Rapid Key Dialing, or 11 to 30 for Speed Dialing). Press: START Press: RECEPTION MODE FEB 1 10:30 A. M. TEL FAX FEB 1 10:30 A. M. TEL FAX FEB 1 10:30 A. M. FAX mode: The fax automatically answers on four rings and receives the incoming document. (Refer to the letter entry table in ENTERING YOUR NAME RECEIVING AND NUMBER. ) 7. [. . . ]