User manual SHARP SF-2540

[. . . ] MODEL SF-2540 SF-2530 In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". The symbol " " denotes the copier is not completely de-energized but in a stand-by condition at this "POWER" switch position. If your copier is so marked, please read "I" for "ON" and " " for "OFF". The socket-outlet shall be installed near the equipment and shall be easily accessible. The CE mark logo label is affixed on an equipment in case that the directives described in the above sentence are applicable to the product. [. . . ] #0 Clear ( ) key Press to clear the copy quantity display, or press during a copy run to terminate copying. #1 CLEAR ALL ( ) key Clears all selected settings and returns the copier to the initial settings. #2 START key and indicator Copying is possible when the indicator is on. Initial settings The copier assumes the initial settings when the ) key is pressed and approxCLEAR ALL ( imately 1 minute after the last copy is made in any mode. Except for the paper tray selection, the copier also assumes the initial setting when it is turned on. q Copy ratio: 100% q Automatic exposure q Copy quantity: 0 q All special copier modes are set to off. q Tray select: Copier lower tray, not an optional paper drawer even if installed (At power on, the previously selected tray will again be selected. ) 5 KEY OPERATOR Initial settings can be programmed as desired. See pages 90 and 88 of the KEY OPERATOR'S GUIDE. GENERAL INFORMATION Part names and functions 41 USER MAINTENANCE The document glass and document cover must be kept clean to avoid dirty areas from being copied onto the copies. Document glass and document cover Wipe the document glass and document cover with a soft, clean cloth. q If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents. q If an optional document feeder is installed, wipe the transport belt with a soft, clean cloth. GENERAL INFORMATION User maintenance 42 MAINTENANCE REQUIRED When the message "READY TO COPY. (MAINTENANCE REQUIRED : )" appears, service by an authorised Sharp Service Technician will be required soon. Contact your Service Centre as soon as possible. GENERAL INFORMATION Maintenance required 43 SPECIFICATIONS COPIER Type Copy system Originals Original sizes Copy sizes Desktop Dry, electrostatic transfer system Sheets, bound documents Max. Variable: 50 to 200% in 1% increments, total 151 steps Fixed presets: 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200% (50%, 64%, 77%, 95%, 100%, 121%, 129%, 141%, 200%) Moving optical source, slit exposure (stationary platen) with automatic exposure function Choice of one or two 500-sheet automatic feed paper trays; one manual feed tray with 50-sheet automatic feed capability Heat rollers Magnetic brush development Halogen lamp Local voltage ±10% (For this copier's power supply requirements, see the name plate located on the right hand side at the rear bottom corner of the copier. ) Max. 1. 75 kW for AC 200 ­ 240V power supply) Copying speed (at 100% copy ratio) Continuous copy First-copy time Warm-up time Copy ratio Exposure system Copy paper feed GENERAL INFORMATION Specifications Fusing system Developer system Light source Required power supply Power consumption 44 SPECIFICATIONS Overall dimensions 1205 mm (W) x 650 mm (D) (47-29/64" (W) x 25-19/32" (D)) Approx. 74. 3 kg (163. 9 lbs. ) (with duplex module) 633 mm (W) x 650 mm (D) x 607 mm (H) (24-59/64" (W) x 25-19/32" (D) x 23-29/32" (H)) Weight (with optional document cover SF-CV13) Copier dimensions (with optional document cover SF-CV13) Operating conditions Temperature: 15°C to 30°C (59°F to 86°F) Humidity: 20% to 85% Document cover (SF-CV13) Reversing automatic document feeder (SF-A58) 20-bin sorter (SF-S15) 20-bin staple sorter (SF-S56) Stand/3000-sheet paper drawer (SF-D23) Stand/500-sheet paper drawer (SF-D24) Duplex module (SF-DM11) 500-sheet paper drawer (SF-CM11) Cassette (SF-IC11) Card counter (SF-EA11) Auditor (SF-EA12) Counter commander (SF-EA13) Personal counter (SF-71A/71B) Optional equipment DUPLEX MODULE (when installed) Paper type Number of copies Ordinary paper only GENERAL INFORMATION 50 (A5, A4, A4R (8-1/2" x 11", 8-1/2" x 11"R)) 30 (B4, A3 (8-1/2" x 14", 11" x 17")) A5, A4, A4R, B4, A3 (8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 14", 11" x 17") In some regions, 216 mm x 330 mm (8-1/2" x 13") size can be used additionally. to 21 lbs. ) Copy paper size Specifications Copy paper weight Specifications are subject to change for improvement without notice. 45 MEMO OPTIONAL EQUIPMENT 46 OPTIONAL EQUIPMENT CONTENTS q q Page q q SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-BIN SORTER (SF-S15)/ 20-BIN STAPLE SORTER (SF-S56) . . . . . . . . . . . . . . . . . . . . . . . . . . . STAND/3000-SHEET PAPER DRAWER (SF-D23)/ STAND/500-SHEET PAPER DRAWER (SF-D24) . . . . . . . . . . . . . . . . . q Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 49 49 49 50 54 55 57 58 58 59 60 61 63 64 66 68 70 71 71 72 74 75 OPTIONAL EQUIPMENT 47 SYSTEM CONFIGURATION The options which are available for the SF-2540 are shown below. 20-bin sorter (SF-S15) Reversing automatic document feeder (SF-A58) Duplex module (SF-DM11) Document cover (SF-CV13) Cassette (SF-IC11) 20-bin staple sorter (SF-S56) Stand/3000-sheet paper drawer (SF-D23) 500-sheet paper drawer (SF-CM11) System configuration OPTIONAL EQUIPMENT Stand/500-sheet paper drawer (SF-D24) q q q q Card counter (SF-EA11) Auditor (SF-EA12) Counter commander (SF-EA13) Personal counter (SF-71A/71B) NOTE: Operating instructions follow for the Document Feeder (SF-A58), Sorters (SF-S15 and SF-S56), Stand/3000-Sheet Paper Drawer (SF-D23), and Stand/500-Sheet Paper Drawer (SF-D24). For the Card Counter (SF-EA11), the Auditor (SF-EA12) and the Counter Commander (SF-EA13), see their manual. 48 REVERSING AUTOMATIC DOCUMENT FEEDER (SF-A58) The reversing automatic document feeder (RADF) will handle A5 to A3 (5-1/2" x 8-1/2" to 11" x 17") originals. Two-sided originals can be copied automatically without having to manually turn them over. PART NAMES Feeding roller cover Original guides Document feeder tray Document feeder cover Exit roller cover Document feeder indicators Document feeder indicators Original feed indicator Indicates the originals in the tray will be fed. Original reminder Indicates an original is still on the document glass. Specifications Acceptable originals Single-sided originals: 50 to 128 g/m2 (14 to 34 lbs. ) Two-sided originals: 50 to 128 g/m2 (14 to 34 lbs. ) for A5 and A4 (5-1/2" x 8-1/2" and 8-1/2" x 11") originals. 50 to 110 g/m2 (14 to 29 lbs. ) for B4 and A3 (8-1/2" x 14" and 11" x 17") originals. [. . . ] When P83 is entered, the following message will appear. P83: ENABLING OF PC/MODEM ACCESS. 1. YES 2. NO To permit remote access to key operator programs without key operator code entry, press key 1. NOTE: The customers must choose the setting of this program by themselves. If "YES" is selected, external operators can access the key operator programs from a computer or other equipment without key operator code entry. [. . . ]