User manual SHARP SF-2014/2114

[. . . ] For quick reference during copier use, keep this manual in a handy location. The AL-1020/SF-2014/2114 /AL-1521 can also be used as a laser printer if an optional printer upgrade kit is installed. q The AL-1020 and SF-2014/2114 are equipped with one paper tray while the AL1250 and AL-1521 are equipped with two paper trays. The illustrations in this manual are mainly for the AL-1020 and SF-2014/2114. [. . . ] The exposure indicator marked "1" will light up, indicating the toner save mode is selected. 4 Special functions 4 Press the exposure mode selector key twice. The photo ( ) indicator will stop blinking and the AUTO indicator will light up steadily. To return to the standard mode, repeat the procedure but use the dark ( key to select exposure level "5" in step 3. ) USER PROGRAMS (power save modes, auto clear time, stream feeding mode) The user programs allow the parameters of certain functions to be set, changed, or canceled as desired. Setting the power save modes, auto clear time, and stream feeding mode 1 2 Press and hold down the light ( ) and dark ( 5 seconds until all the alarm indicators ( , display. ) keys simultaneously for more than , ) blink and "­ ­" appears in the Use the left copy quantity ( ) key to select a user program number (1: auto clear time, 2: preheat mode, 3: auto power shut-off timer, 4: stream feeding mode, 5: auto power shut-off mode). The selected number will blink in the left side of the display. 26 USER PROGRAMS 3 4 Press the print ( ) key. The entered program number will be steadily lit and the currently selected parameter number for the program will blink on the right side of the display. Select the desired parameter using the right copy quantity ( parameter number will blink on the right of the display. 1 2 3 4 5 Mode Auto clear time Preheat mode Auto power shutoff timer Stream feeding mode Auto power shutoff mode 0 e OFF 3 e 90 sec. 0 e OFF 0 e OFF * 1 e ON * 1 e ON 4 Special functions Factory default settings are indicated with an asterisk (*). 5 Press the print ( ) key. The right-hand number in the display will be steadily lit and the entered value will be stored. To change the setting or to set another mode, press the clear ( copier will return to step 2. ) key. The 6 Press the light ( ) or dark ( ) key to return to the normal copy mode. DISPLAYING TOTAL NUMBER OF COPIES Use the following procedure to display the total number of copies. 1 Press the clear ( ) key to reset the display to zero. 2 Press and hold down the clear ( ) key for approximately 5 seconds. Dispose of the old drum cartridge in accordance with local regulations. 29 DRUM CARTRIDGE REPLACEMENT 4 Remove the new drum cartridge from the protective bag and remove the protective cover from the cartridge. Then gently install the new drum cartridge. Do not touch the surface of the drum (green portion) of the cartridge. Doing so may cause smudges on the copies. 5 6 Gently install the TD cartridge. To install the TD cartridge, see page 12, INSTALLING THE TD CARTRIDGE. Close the front cover and then the side cover by pressing the round projections near the side cover open button. The drum replacement required ( ) indicator will go out and the ready ( ) indicator will light up. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. 5 Supplies and user maintenance 30 USER MAINTENANCE USER MAINTENANCE Proper care is essential in order to get clean, sharp copies. Before cleaning, be sure to turn the power switch off and remove the power cord from the outlet. Do not use thinner, benzene or other volatile cleaning agents. Doing so may cause deformation, discoloration, deterioration or malfunction. Cabinet Wipe the cabinet with a soft, clean cloth. Original table and original cover Stains on the glass, cover or SPF roller will also be copied. Original table Original cover SPF roller 5 Supplies and user maintenance 31 USER MAINTENANCE Transfer charger If copies start becoming streaky or blotchy, the transfer charger may be dirty. [. . . ] Upon your receipt of the exchange unit, packing and shipping instructions will be enclosed for you to return the defective unit. Upon Sharp's receipt of the defective unit, your credit card hold will be released. How Warranty Repair Service is Obtained If you prefer that we repair your unit instead of replacing it, our Customer Relations Specialists at 1630-378-3590 will explain how to obtain warranty repair service. Please be sure to retain the original packaging materials in order to facilitate shipment. The shipment of the defective unit will be at your expense; please be sure it is insured and packaged securely. [. . . ]