User manual SHARP RP-Z2000H

[. . . ] · Be sure your appliance is installed and grounded properly by a qualified installer or service technician. · To eliminate the need to reach over the cooktop, cabinet storage space above the cooktop should be avoided or a range hood installed. To reduce the risk of tipping the appliance, it must be secured by the Anti-Tip bracket attached to the appliance. · This appliance must be electronically grounded in accordance with local codes, or in their absence, with the National Electrical Code ANSI/NFPA No. · The installation of appliances designed for manufactured (mobile) home installation must conform with Manufactured Home Construction and Safety Standard, title 24CFR, part 3280 [Formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD (part 280)] or when such standard is not applicable, the Standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups), ANSI Z225. [. . . ] · The installation of appliances designed for manufactured (mobile) home installation must conform with Manufactured Home Construction and Safety Standard, title 24CFR, part 3280 [Formerly the Federal Standard for Mobile Home Construction and Safety, title 24, HUD (part 280)] or when such standard is not applicable, the Standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups), ANSI Z225. · Make sure the wall coverings and the cabinets around the appliance can withstand the heat generated by the appliance. Never leave children alone or unattended in the area where an appliance is in use. Stepping, leaning or sitting on the drawer of this appliance can result in serious injuries and can also cause damage to the appliance. · Do not store items of interest to children in the cabinets above the appliance. Children could be seriously burned climbing on the appliance to reach items. · To eliminate the need to reach over the cooktop, cabinet storage space above the cooktop should be avoided. · Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance. · Reset all controls to the "off" position after using a programmable timing operation. UNPACKING AND EXAMINING YOUR APPLIANCE 1 Remove all packing materials from inside the Microwave Drawer. Waveguide Cover DO NOT REMOVE THE WAVEGUIDE C OV E R , wh ich i s located on the top of the Microwave Drawer cavity. To correct, slide the appliance out one inch and follow instructions from F above. Figure 11 5 INSTALLATION MANUAL I MAKE SURE THE EDGE OF THE COUNTERTOP FITS FLUSH AGAINST THE END OF THE FRONT CONTROL PANEL. 70-Latest Edition. Effective January 1, 1996, the national Electrical Code requires that new, but not existing, construction utilize a four-conductor connection for this appliance class. When installing this appliance in new construction, a mobile home, recreational vehicle or an area where local codes prohibit grounding through the neutral conductor, follow the instructions in the section on NEW CONSTRUCTION AND FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTOR. ELECTRICAL SHOCK HAZARD · Electrical ground is required on this appliance. · Do not connect to the electrical supply until appliance is permanently grounded. Figure 15 · DISCONNECT POWER TO THE CIRCUIT BREAKER OR FUSE BOX BEFORE MAKING THE ELECTRICAL CONNECTION. CHECKING INSTALLATION To check if the device is installed and engaged properly, open the Microwave Drawer fully and gently apply medium force in the center of the handle until movement of the appliance is detected. Continue pressing until the Anti-Tip bracket is engaged and movement stops. A small amount of movement is acceptable at the back of the appliance top, but it should be stable and not tip once the Anti-tip bracket is engaged. Stop pressing on the Microwave Drawer handle and close. · This appliance must be connected to a grounded, metallic, permanent wiring system or the grounding connector of the power cord should be connected to the grounding terminal or wire lead on the appliance. · Failure to heed these warnings could result in a fire, personal injury or electrical shock. To check that the unit will not slide out, open the Microwave Drawer fully and then apply gentle outward pressure. If the unit does slide, check installation beginning with C on page 5. ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on the rating plate. (Rating Plate is located on the faceplate behind the Microwave Drawer front. ) See Figure 16. Breaker or fuse size: 240V 208V 40 Amps 40 Amps Rating plate Figure 16 All electrical wiring and hookup for this appliance should be by a qualified electrician. [. . . ] (Rating Plate is located on the faceplate behind the Microwave Drawer front. ) See Figure 16. Breaker or fuse size: 240V 208V 40 Amps 40 Amps Rating plate Figure 16 All electrical wiring and hookup for this appliance should be by a qualified electrician. Check with local utilities for electrical codes which apply in your area. Failure to wire your appliance according to governing codes could result in hazardous conditions. [. . . ]