User manual SHARP PN-L703B ANNEXE 1

[. . . ] PN-L703B PN-L603B LCD MONITOR OPERATION MANUAL IMPORTANT: To aid reporting in case of loss or theft, please record the product’s model and serial numbers in the space provided. The numbers are located in the rear of the product. Model No. : Serial No. : U. S. A. ONLY IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:  REDUCE THE RISK OF ELECTRIC TO SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within a triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] D-SUB1 ENTER Select the input mode to be used in D-Sub1 input terminal. HDMI AUTO VIEW When ON is selected, the screen size is adjusted automatically according to the screen size control signal included in the video signal input from the AV HDMI input terminal. HOT PLUG CONTROL Sets whether to use hot plug control for the HDMI1, HDMI2, and HDMI3 input terminals. INPUT MODE NAME For each terminal, you can change the input mode name that is displayed during input mode selection and display. AUDIO SELECT Selects the terminal used to input audio signals in each input mode. AUDIO OUTPUT Sets the volume of sound output from the audio output terminals. When set to VARIABLE 2, sound will not be output from the built-in speaker or the external speaker terminal. AUDIO INPUT LEVEL 1/2 Selects the maximum audio input level of the audio input 1, 2 terminals. 31 E Menu Items TOUCH INPUT SELECT These settings enable use of the touch panel according to input mode selection. BOTTOM USB Sets which input mode the touch panel connected to the USB 1 port is used in. Select the terminal into which the video signal of the computer connected to the USB 1 port will be input. is selected and the input mode is DisplayPort, HDMI1, or D-SUB1, the touch panel can be used with the computer connected to the USB 1 port. SIDE USB Sets which input mode the touch panel connected to the USB 2 port is used in. Select the terminal into which the video signal of the computer connected to the USB 2 port will be input. is selected and the input mode is HDMI2, HDMI3, or D-SUB2, the touch panel can be used with the computer connected to the USB 2 port. LAN SETUP Configures the settings to control the monitor from the computer via LAN. (See page 40. ) E 32 Menu Items nMONITOR OSD H-POSITION Adjusts the horizontal display position of menu screen. STANDBY MODE When STANDARD is selected, startup time from standby mode is reduced. When LOW POWER is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the startup time from standby mode becomes longer. OFF IF NO OPERATION Determines whether or not to set the monitor to go into standby mode when there is no operation from the remote control unit, or LAN for over 4 hours. POWER ON DELAY If SET is set to ON, you can delay the screen display after the monitor is turned on. When ON is selected, set the delay time with INTERVAL (interval can be set up to 60 seconds in units of 1 second). [. . . ] DPMS: Display Power Management Signaling DPMS ON STATE STANDBY SUSPEND OFF STATE Screen Display No display Power Hsync consumption*1 225 W 185 W 14 W *2 14 W *2 Yes No Yes No Vsync Yes Yes No No *1  Upper value: PN-L703B, Lower value: PN-L603B. are set to OFF. nDDC (plug and play) The monitor supports the VESA DDC (Display Data Channel) standard. DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters is exchanged between the two. [. . . ]