User manual SHARP PG-LX2000

[. . . ] In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 5A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below: WARNING: THIS APPARATUS MUST BE EARTHED. [. . . ] If you want to change the on-screen display to another language, change the language according to the procedure on page 60. Remove the lens cap and press projector or on the on the remote control. · The power indicator illuminates green. · After the lamp indicator illuminates, the projector is ready to start operation. See page 53 for details. ON button STANDBY button Power indicator Lamp indicator Note · The lamp indicator illuminates or blinks, indicating the status of the lamp. · When switching on the projector, a slight flickering of the image may be experienced within the first minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilizing the lamp output characteristics. · If the projector is put into standby mode and immediately turned on again, the lamp may take some time to illuminate. ON button Basic Operation STANDBY button On-screen Display Turning the Power off (Putting the Projector into Standby Mode) 1 Press on the projector or on the remote control, then press that button again while the confirmation message is displayed, to put the projector into standby mode. Unplug the power cord from the AC outlet after the cooling fan stops. Info · Do not unplug the power cord during projection or cooling fan operation. The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode. This can cause damage due to rise in internal temperature, as the cooling fan also stops. -29 2 Image Projection Using the Adjustment Feet The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector when the screen is located higher than the projector, the screen is inclined or when the installation site is slightly inclined. Install the projector so that it is as perpendicular to the screen as possible. Side View Top View Lens center 1 2 Press the HEIGHT ADJUST button. · The front adjustment foot comes out. Lift the projector to adjust its height while pressing the HEIGHT ADJUST button. · The projector is adjustable up to approximately 12 degrees (6 steps). Used for projecting images from equipment connected to the VIDEO input terminal. Used for projecting images from equipment connected to the S-VIDEO input terminal. Using Component INPUT 3 mode Using Video INPUT 4 mode Using S-Video Adjusting the Volume Press \ /| on the projector or VOL | / on the remote control to adjust the volume. Volume buttons Note · Pressing Pressing or \ will lower the volume. or | will raise the volume. "On-screen Display Basic Operation -33 Image Projection Displaying the Black Screen and Turning off the Sound Temporarily Press on the remote control to temporarily display a black screen and turn off the sound. Note · Pressing again will turn the projected image and sound back on. "On-screen Display AV MUTE button Displaying an Enlarged Portion of an Image Graphs, tables and other portions of projected images can be enlarged. This is helpful when providing more detailed explanations. MOUSE/Adjustment button ('/"/\/|) ENLARGE (Enlarge/Reduce) buttons 1 Press · Pressing on the remote control. or enlarges or reduces · Enlarges the image. UNDO button RESIZE button the projected image. Note ×1 ×2 ×3 ×4 ×9 ×16 ×36 ×64 · You can change the location of the enlarged image using ', ", \ and |. 2 Press on the remote control to cancel the operation. · The magnification then returns to ×1. Note In the following cases, the image will return to the normal size (×1). · When the input signal resolution and refresh rate (vertical frequency) change. -34 Freezing a Moving Image 1 2 Press on the remote control. FREEZE button · The projected image is frozen. Press again to return to the moving image from the currently connected equipment. Selecting the Picture Mode You can select the suitable picture mode for the projected image, such as movie or video game. Press STANDARD on the remote control. , the picture mode changes CINEMA GAME PRESENTATION · When pressing in order of UNDO button Basic Operation PICTURE MODE button Note · You can also use on the projector. · This function can also be accessed from the OSD menu (see page 44). -35 Image Projection This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose "NORMAL", "DOT BY DOT", "BORDER" or "STRETCH" image. Resize Mode Press · Pressing MOUSE/Adjustment button ('/"/\/|) on the remote control. changes the display as shown on UNDO button pages 36 and 37. while · To return to the standard image, press "RESIZE" is displayed on the screen. · This function can also be accessed from the OSD menu (see page 49). RESIZE button COMPUTER NORMAL SVGA (800 × 600) XGA (1024 × 768) SXGA (1280 × 960) SXGA+ (1400 × 1050) SXGA (1280 × 1024) 1280 × 720 DOT BY DOT 800 × 600 -- 1280 × 960 1400 × 1050 1280 × 1024 -- BORDER STRETCH 4:3 aspect ratio 1024 × 768 768 × 576 1024 × 576 Other aspect ratios 960 × 768 -- 720 × 576 -- 960 × 576 1024 × 576 Input Signal Computer Image type NORMAL Output screen image DOT BY DOT BORDER STRETCH Resolution lower than XGA 4:3 aspect ratio * * * * XGA 4:3 aspect ratio * * Resolution higher than XGA 4:3 aspect ratio * * SXGA (1280 × 1024) 5:4 aspect ratio * * 1280 × 720 16:9 aspect ratio * Mode for projecting an image with the original aspect ratio without cutting any portions. : Cutout area on which images cannot be projected. : Area where the signals are off screen. Note · If "RESIZE" is displayed when you have set "DOT BY DOT" and signals having a higher resolution than XGA are being input, you can move the image so that it appears entirely within the panel by using the adjustment buttons ('/"/\/|) on the remote control. [. . . ] 9 Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38, 44 Picture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]