User manual SHARP PG-D2870W

[. . . ] Introduction DATA PROJECTOR MODEL Easy Start PG-D3550W PG-D3050W PG-D2870W OPERATION MANUAL Setup Connections Basic Operation Useful Features PG-D3550W/PG-D3050W Appendix IMPORTANT · For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. · Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 11. Model No. : Serial No. : ii SPECIAL NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. [. . . ] (Move the slide bar in the + direction. ) 2 Press P/Q or O/R to adjust the Keystone Correction. Basic Operation Note · To return to the default setting, press RETURN while the on-screen display of the Keystone Correction mode is on the screen. Shrinks lower side. (Move the slide bar in the - direction. ) 3 Press KEYSTONE. · The on-screen display of the Keystone Correction mode will disappear. Info · While adjusting the image using Keystone Correction, straight lines and the edges of the image may appear jagged. 29 Image Projection (Continued) Switching the Input Mode Select the appropriate Input mode for the connected equipment. Use INPUT / to select the Input mode, and use O/Q to select the audio input terminal. INPUT buttons AV MUTE button VOL +/­ (Volume) buttons O/Q buttons Adjusting the Volume Press VOL +/­ on the remote control or ­O/Q+ on the projector to adjust the volume. Note · Pressing VOL­/­O will lower the volume. · When the projector is connected to external equipment, the volume level of the external equipment changes in accordance with the volume level of the projector. Set the projector's volume to the lowest level when turning the projector on/off or when changing the input signal. · When you do not want to output the sound from the projector's speaker while the projector is connected to external equipment, set "Speaker" in the "PRJ-ADJ1" menu to "Off". (See page 50. ) On-screen display Displaying the Black Screen and Turning Off the Sound Temporarily Press AV MUTE on the remote control or close the lens shutter to temporarily display a black screen and turn off the sound. On-screen display Note · Pressing AV MUTE again will turn the projected image back on. · When you close the lens shutter, the projector will be set to AV Mute mode and then the projector will be turned off automatically after about 30 minutes. 30 Resize Mode This function allows you to modify or customize the Resize mode to enhance the input image. Press RESIZE. · See page 47 for setting on menu screen. RESIZE button NORMAL FULL NATIVE 800 × 600 1068 × 800 1024 × 768 1152 × 864 1400 × 1050 1000 × 800 1280 × 720 1280 × 722 1280 × 720 1280 × 768 1280 × 800 -- Output screen image 1280 800 1280 × 1024 -- 1360 × 768 1366 × 768 -- 1280 × 720 -- 1280 × 720 16:9 COMPUTER SVGA (800 × 600) 4:3 aspect ratio XGA (1024 × 768) SXGA (1152 × 864) SXGA+ (1400 × 1050) SXGA (1280 × 1024) 1280 × 720 Other aspect ratios 1360 × 768 1366 × 768 1280 × 768 1280 × 800 Input signal Computer Resolution XGA and below Resolution higher than XGA *3 4:3 aspect ratio Image type NORMAL FULL NATIVE 16:9 *1 Basic Operation SXGA (1280 × 1024) 5:4 aspect ratio 1280 × 720 16:9 aspect ratio 1360 × 768 1366 × 768 16:9 aspect ratio *1 1280 × 768 15:9 aspect ratio 1280 × 800 16:10 aspect ratio : Cutout area on which images cannot be projected : Area where the signals are off screen *1 The Image Shift function can be used for these images. --*2 --*2 *1 --*2 --*2 *1 *1 *1 31 Image Projection (Continued) VIDEO/DTV Input signal Video/DTV Image type NORMAL Output screen image AREA ZOOM V-STRETCH 16:9 *1 4:3 aspect ratio 480I, 480P, 576I, 576P, NTSC, PAL, SECAM *1 Squeeze *1 Letter box *1 720P, 1035I, 1080I, 1080P 16:9 aspect ratio *1 16:9 aspect ratio *1 16:9 aspect ratio 540P *1 16:9 aspect ratio (4:3 aspect ratio in 16:9) : Cutout area on which images cannot be projected : Area on which the image is not included in the original signals *1 The Image Shift function can be used for these images. --*2 About Copyrights · When using the Resize function to select an image size with a different aspect ratio to a TV program or video image, the image will look different from its original appearance. · The use of the Resize or Keystone Correction function to compress or stretch the image for commercial purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. Please use caution. 32 Operating with the Remote Control BREAK TIMER button FREEZE button MAGNIFY buttons POINTER button SPOT button Adjustment buttons (P/R/O/Q) EFFECT button PICTURE MODE button ECO+QUIET button AUTO SYNC button Displaying the Pointer 1 Press POINTER and press P/R/ O/Q on the remote control to move the pointer. · Press EFFECT to change the pointer icon (5 types). Star Finger1 Finger2 Heart Underline 2 Press POINTER again. · The pointer will disappear. Using the Spot Function Displaying and Setting the Break Timer 1 1 Press BREAK TIMER. · The timer starts to count down from 5 minutes. Press SPOT and press P/R/O/Q on the remote control to move the spot area. · Press EFFECT to change the spot area size (3 types). 1/9 1/25 1/8 On-screen display 2 Press P/R/O/Q to adjust the length of the break time. · Increases with P or Q · Shortens with O or R 2 Press SPOT again. · The spot area will disappear. 5 minutes 6 minutes 60 minutes 4 minutes 3 minutes 1 minute · The break time can be set in units of one minute (up to 60 minutes). Switching the Eco+Quiet Mode Press ECO+QUIET to switch the Eco+Quiet mode between on and off. · When the Eco+Quiet Mode is set to "ON", the sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend. Useful Features Canceling the break timer display function Press BREAK TIMER. Note · The Break Timer is not available while the projector is operating the following functions. - Auto Sync - Freeze - AV Mute - Input Search Note · Refer to "Eco+Quiet" on page 44 for details. 33 Operating with the Remote Control (Continued) Auto Sync (Auto Sync Adjustment) Auto Sync function works when detecting input signal after the projector turns on. Press AUTO SYNC to manually adjust with Auto Sync function. Note · When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page 45. ) Displaying an Enlarged Portion of an Image Graphs, tables and other portions of projected images can be enlarged. This is helpful when providing more detailed explanations. 1 Press MAGNIFY on the remote control. · Enlarges the image. · Pressing or MAGNIFY enlarges or reduces the projected image. Note Press . ×3 ×4 Freezing a Moving Image ×1 ×2 Press . 1 2 Press FREEZE. · The projected image is frozen. · You can change the location of the enlarged image using P, R, O and Q. Press FREEZE again to return to the moving image from the currently connected device. 2 Press RETURN on the remote control to cancel the operation. · The magnification then returns to 1. Note Selecting the Picture Mode You can select the appropriate Picture mode for the projected image, such as movie or video game. Press PICTURE MODE. · When pressing PICTURE MODE, the Picture mode changes in the following order: STANDARD PRESENTATION MOVIE GAME sRGB* · The selectable magnifications differ depending on the input signal. · In the following cases, the image will return to the normal size ( 1). [. . . ] · Cables are incorrectly connected to the projector or the connected equipment works improperly. While the remaining lamp life draws to a close, replace the lamp. 21­25 61 61 15 15 This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes. 66 For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the "Troubleshooting" section on pages 65 and 66. [. . . ]