User manual SHARP MD-M1

[. . . ] MD MICRO SYSTEM OPERATION MANUAL MODEL MD-M1 Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. MD-M1 MD micro system consisting of MD-M1 (main unit) and CP-M1 (speaker system). Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] To identify different sections of a recording you can increase the track number at any point during the recording process. To create a new track number, while in the recording mode, press the q REC button. q The track number will increase by one, and then the recording will continue. 4 3 5 H 1 Tune in to the desired station. 3 Press the q REC button. q The unit will enter the recording stand-by mode. 4 Check the recordable time by pressing the DISPLAY button. Note: q Before recording an AM broadcast, enter the recording stand-by mode, and then separate the AM loop antenna from the main unit. q During recording, you cannot change the station. 5 Press the 0 6 button. 23 EDITING s What the editing function can do You can create original discs using the MD editing function, on which you can change the order of the tracks and you can create disc or track names. q Playback-only MiniDiscs cannot be edited. DIVIDE A single track can be divided into two at any desired position. q The numbers of the tracks which come after the newly divided track will be automatically increased by one. 1 2 3 TRACK/DISC NAME Discs and tracks (up to 255 tracks per disc) can be named. Since track names are displayed when the beginning of each track is located or during playback, you can quickly check the name of each track. q Capital letters, numbers and symbols can be used. (Pages 25, 26) A 1 2 B 3 C D 4 s Type of characters used Type of characters Characters (Symbols) ABCDEFGH I J KL MNOPQ A B C D (Page 28) Capital letters RS T UVWXYZ 1 ( 2 ) 3 4 + 5 , 6 7 . " # $ %& ' COMBINE Two consecutive tracks can be combined into one track. q The numbers assigned to the tracks following the combined tracks will be decreased by one automatically. 1 2 3 4 Symbols ?@< = > _ Number of characters you can enter q Disc names and track names Up to 40 characters (including spaces) can be entered for each name. If more than 40 characters are entered, "NAME FULL" will appear. q Total number of characters per MiniDisc A total of approximately 1, 700 characters can be used for all of the disc and track names. If more than 1, 700 characters are entered, " TOC FULL " will appear. To record the results, select another input or set the unit to the stand-by mode. During writing, the "TOC" goes out, all editing changes have been recorded to the disc. Note: q Storing the edited contents on the disc can be done after several pieces of editing have been finished. A 1 B 2 3 C D A B C D (Pages 28, 29) ERASE/ALL ERASE Tracks you want to erase can be erased one at a time or all at once. q Once a track has been erased, it cannot be recovered. Double-check the track number before erasing it. 1 2 3 4 5 A 1 2 B C 3 D 4 E A B D E (Page 30) MOVE A designated track can be moved to any desired position. q The numbers assigned to the tracks following the track which is moved will be adjusted automatically. 1 2 3 4 A 1 2 B 3 C 4 D C A B D (Page 29) 24 (Continued) s To create a disc name A name for the whole disc. (Remote control operation) REC SLEEP 5 Select the character you want pressing the or button. REC SLEEP NAME/ TOC EDIT DISPLAY ENTER / CLEAR 6 Press the ENTER button to enter the character. REC SLEEP q Repeat steps 4 to 6 above to enter the characters in the name. When the next character's type is the same as the previous character, step 4 can be skipped. 7 After entering all of the characters in the name, press the NAME/TOC EDIT button. 1 Press the s button after pressing the MD button. q The total number of tracks and the total playing time on an MD will appear. q The disc name will be recorded. REC SLEEP 2 Press the NAME/TOC EDIT button, and then select "DISC NAME" pressing the button. DISC TOC TRACK TOTAL REMAIN REC SLEEP To erase a disc name: or 1 2 After performing steps 1 to 3. Press the ENTER button. 3 Within 10 seconds, press the ENTER button. DISC DISC REC SLEEP Notes: q Up to 40 characters can be entered. q This function cannot be used in the random play mode and APMS play mode. q The unit will enter the character input mode. 4 Press the DISPLAY button to select the type of characters you want to use. Capital letters Symbols 25 (Continued) s To create a track name Name each track. [. . . ] q General Power source: Power consumption: Dimensions: AC 120 V, 60 Hz 60 W Width; 6-5/16" (160 mm) Height; 9-1/2" (240 mm) Depth; 11-13/16" (300 mm) Weight: 9. 7 lbs. (4. 4 kg) q Compact disc player section Type: Top open type compact disc player Signal readout: Rotation speed: Error correction: Quantization: Frequency response: D/A converter: Dynamic range: Wow and flutter: Non-contact, 3-beam semiconductor laser pickup 200 - 500 rpm CLV, Approx. CIRC (Cross Interleave ReedSolomon Code) 16-bit linear 20 - 20, 000 Hz 1-bit D/A converter 90 dB (1 kHz) Unmeasurable (less than 0. 001% W. peak) q Amplifier section Output power: FTC 16 watts per channel minimum RMS into 4 ohms from 80 Hz to 20 kHz with no more than 10% total harmonic distortion Output terminals: Speaker; 4 ohms Headphones; 16 - 50 ohms (recommended 32 ohms) Input terminals: AUX; 500 mV/47 k ohms Signal/noise ratio: 95 dB (1 kHz) q MiniDisc recorder section Type: MiniDisc recorder Signal readout: Rotation speed: Error correction: Non-contact, 3-beam semiconductor laser pickup 400 - 900 rpm CLV, Approx. [. . . ]