User manual SHARP LL-H1513 OPERATION MANUAL

[. . . ] LCD MONITOR MONITEUR LCD MONITOR LCD MONITOR LCD !"==== ! LL-H1513 OPERATION MANUAL MODE D'EMPLOI MANUAL DE FUNCIONAMIENTO MANUAL DE INSTRUÇÕES !" Table of Contents Notice for Users in the USA . 10 Height adjustment, angle adjustment, rotation (long height/width) . 33 3 English Español Italiano Français Deutsch English Notice for Users in the USA FCC Statement WARNING ­ FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] The ADJUSTMENT Menu will be displayed. ADJUSTMENT MANUAL CLOCK PHASE H-POS V-POS INPUT-1 1024 x 768 ANALOG V : 60Hz 60 24 101 20 H : 48. 4kHz AUTO On Screen Display for the automatic adjustment First display an image that makes the entire screen light. If you are using Windows, you can use the Adjustment Pattern on the accompanying CDROM. Opening the Adjustment Pattern (for Windows) This explanation is for Windows 95/98/2000/Me/ XP, and assumes that the CD-ROM drive is "D drive". - It may not be possible to achieve correct adjustment with the first automatic adjustment. - When the computer's video input signals are Composite Sync or Sync On Green. (Automatic adjustments may not be possible. ) - When [OUT OF ADJUST] is displayed. (When the screen displays an entirely dark image, the automatic screen adjustment may be disabled. When making an automatic adjustment, be sure to either use the Adjustment Pattern or try displaying an image that makes the entire screen very bright. ) - Automatic adjustment may not be achieved correctly depending on what is displayed on the screen - moving pictures or the MS-DOS prompt etc. After completing the adjustments, press the computer's [Esc] key to exit the Adjustment Program. Note: - If your computer's display mode is set to 65K colors, you may see the different color levels in each color pattern or the gray scale may look colored. (This is due to the specification of the input signal and is not a malfunction. ) 18 Adjusting the screen display (When using an analog signal) English English Español Italiano Français Deutsch Manual screen adjustment Adjustments can be made using On Screen Display (OSD) Menu provided. ADJUSTMENT Menu ADJUSTMENT MANUAL CLOCK PHASE H-POS V-POS INPUT-1 1024 x 768 ANALOG V : 60Hz 60 24 101 20 H : 48. 4kHz AUTO On Screen Display for adjustment If you are using Windows, open the Adjustment Pattern on the accompanying CD-ROM. 18) If your system is not Windows, you can not use the Adjustment Pattern. Therefore display an image that makes the entire screen light and adjust it through checking visually its actual tone. This chapter provides the procedure how to adjust the screen by using Adjustment Pattern (for Windows) MANUAL: Individual menu options are manually adjusted. - To choose a menu option: SELECT button - To go to the next menu: MENU button CLOCK The figure below demonstrates how to adjust so that vertical flicker noise is not emitted. The ADJUSTMENT Menu will be displayed. ADJUSTMENT MANUAL CLOCK PHASE H-POS V-POS INPUT-1 1024 x 768 ANALOG V : 60Hz 60 24 101 20 H : 48. 4kHz AUTO At this point relevant menu options can be adjusted. (ADJUSTMENT GAIN CONTROL COLOR CONTROL MODE SELECT OSD Menu disappears) Note: - The OSD Menu automatically disappears approximately 30 seconds after the last command. Vertical flicker noise PHASE The figure below demonstrates how to adjust so that horizontal flicker noise is not emitted. ( buttons) Note: - Adjustments to PHASE should be made only after CLOCK has been correctly set. Horizontal flicker noise H-POS (horizontal positioning) and V-POS (vertical positioning) To center the screen image within the boundaries of the screen, adjust the left-right (H-POS) values and the up-down (V-POS) values. ( buttons) Screen frame 19 Adjusting the screen display (When using an analog signal) GAIN CONTROL Menu GAIN CONTROL MANUAL BLACK LEVEL CONTRAST 50 18 AUTO COLOR CONTROL Menu COLOR CONTROL COLOR MODE WHITE BALANCE HUE SATURATION sRGB 0 0 STD VIVID INPUT-1 1024 x 768 ANALOG V : 60Hz H : 48. 4kHz INPUT-1 1024 x 768 ANALOG V : 60Hz H : 48. 4kHz MANUAL: Individual menu options are manually adjusted. AUTO: Every menu option is automatically adjusted using the Auto Gain Control* function. - To choose a menu option: SELECT button - To go to the next menu: MENU button * Auto Gain Control function - The Auto Gain Control adjusts contrast and black level based on the brightest color of the image displayed. Unless an Adjustment Pattern is used, automatic adjustment may not be possible. - If the signal coming from the computer is composite sync or sync on green, automatic adjustment cannot be performed. [. . . ] - When using the ColorSync profile, set [COLOR MODE] and [WHITE BALANCE] to [STD], and set [HUE] and [SATURATION] to [0]. Setting up the ColorSync profile Notes: - In addition, it is necessary to have PC Exchange or File Exchange installed in your system. - Depending on the type of computer or OS, command names and methods may differ. Please follow the computer's own operation manual while reading this. Copy the profile used by the application disk to the ColorSync profile folder in the system folder. [. . . ]