User manual SHARP LC-32A47E

[. . . ] LC-32A47E LCD COLOUR TELEVISION LCD-FARBFERNSEHGERÄT OPERATION MANUAL BEDIENUNGSANLEITUNG DEUTSCH ENGLISH SPECIAL NOTE FOR USERS IN THE U. K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or )5) and of the same rating as above, which is also indicated on the pin face of the plug, must be used. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type. DANGER: The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. [. . . ] If there is no signal input for eight minutes, the TV enters the standby mode. Even if you start using the PC and the signal inputs again, the TV stays in standby mode. The TV turns on again by pressing a on the TV or B on the remote control unit (Page 5). If there is no signal input for eight seconds, the TV enters the standby mode. When you start using the PC and the signal inputs again, the TV turns on. The TV turns on again by pressing a on the TV or B on the remote control unit (Page 5). Off Mode 1 Repeat steps 1 and 2 in Programme Setup. 1 Programme auto search 2 Auto labelling 3 Auto sorting 4 Preset download Mode 2 · · · Manual Adjust You can set some channel items manually. 1 2 3 4 5 Setup menu Auto Installation You can run "Auto Installation" again, even after setting up the preset channels. Repeat steps 1 and 2 in Programme Setup. Press a/b/c/d to select the channel you want to edit, and then press OK. · The selected channel information displays. 1 Go to "MENU" > "Setup" > "Auto Installation". If you have already set the PIN under "Child Lock", enter it here. · See page 10 for setting PIN. Press a/b to select the desired menu item, and then press OK. Press a/b/c/d to select or adjust. NOTE · When you exit "Manual Adjust" in the "Programme Setup" menu, preset download automatically runs if you change information on that menu. 2 3 Press c/d to select "Yes", and then press OK. You can set the language, location of the TV and country the same as in the Initial auto installation. Follow steps 1 to 3 on page 5. Fine You can adjust the frequency to the desired position. NOTE · Adjust while checking the background picture as a reference. · Instead of pressing c/d to adjust the frequency, you can set by directly entering the frequency number of the channel with 0­9 numeric buttons. Programme Setup This section describes how to set up analogue TV channels manually. EXAMPLE · 179. 25 MHz: Press 1 s 7 s 9 s 2 s 5. · 49. 25 MHz: Press 4 s 9 s 2 s 5 s OK. 9 Menu operations Colour sys. Select the optimum colour systems to receive ("AUTO", "PAL", "SECAM"). Erase Programme Channels can be erased individually. Sound sys. (Broadcasting system) Select the optimum sound systems (Broadcasting systems) to receive ("B/G", "D/K", "I"). 1 2 3 4 Label When a TV channel sends its Network Name, the "Auto Installation" detects the information and assigns a name to it. However, you can change channel names individually. 1 2 3 Repeat steps 1 to 4 in Manual Adjust. Press a/b/c/d to select each character of the new name for the channel, and then press OK. Repeat step 2 until the name is fully spelt out. · The name can be five characters or less. · If a channel name is less than five characters, select "END", then press OK. Repeat steps 1 and 2 in Programme Setup. Press a/b/c/d to select the channel you want to erase, and then press OK. · A message window pops up. 5 Press c/d to select "Yes", and then press OK to erase the selected channel. Repeat steps 3 and 4 until all desired channels are erased. Skip Channels with "Skip" set to "On" are passed over when using Pr/s even if selected while watching the image from the TV. Child Lock Allows you to use a PIN to protect certain settings from being accidentally changed. Decoder When connecting a decoder to the TV, you need to select "EXT3". Changing the PIN 1 2 3 NOTE · The factory preset value is "Off". Lock You can block the viewing of any channel. NOTE · See "Child Lock" for setting PIN. · When "Lock" is set to "On" for a channel, "Child lock has been activated. " displays, and the image and sound of the channel are blocked. [. . . ] Please purchase them at your nearest shop. · Additional optional accessories may be available in the near future. When purchasing, please read the newest catalogue for compatibility and check the availability. Part name Wall mount bracket AN-37AG5 Part number PC compatibility chart Resolution VGA SVGA XGA WXGA WXGA 640 g 480 800 g 600 1024 g 768 1280 g 768 1360 g 768 Horizontal Frequency 31. 5 kHz 37. 9 kHz 48. 4 kHz 47. 7 kHz 47. 7 kHz Vertical Frequency 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz VESA Standard VGA, SVGA, XGA and WXGA are registered trademarks of International Business Machines Corp. NOTE · This TV has only limited PC compatibility, correct operation can only be guaranteed if the video card conforms exactly to the VESA 60Hz standard. · Depending on the graphics card, resolutions of 1360 g 768 may not display correctly. 15 End of life disposal A. [. . . ]