User manual SHARP LC-22LE320E

[. . . ] operation manual Contents Contents 1 introduction 2 Dear SHARP customer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 preparation 5 Supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Quick guide 7 Initial installation overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Watching tV 9 Daily operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When complete, follow the on-screen instructions to exit. 4 5 6 Press oK to start scanning. When the scan is completed, the result of signal strength and signal quality appear on the screen. Follow the on-screen instructions to exit. E Single rF Scan If using digital broadcasts, you can check the quality and signal strength of digital channels. This allows you to reposition and test your antenna or satellite dish. 1 Press menu on the remote control and select tV Channels. note · If the signal quality and strength is poor, reposition the antenna or satellite dish and retest. · If you have further problems with the reception of your digital broadcast, contact a specialised installer. note · You are prompted to enter current password to enter Channels if Channel Block /parental Guidance / input Block in the parental menu is not the default setting. E analogue manual Scan This section describes how to search and store analogue TV channels manually. 2 Press <> to select Single rF Scan and press oK or to enter. 1 Press menu on the remote control and select tV Channels. note · You are prompted to enter current password to enter Channels if Channel Block /parental Guidance / input Block in the parental menu is not the default setting. 14 tV menu 2 Press <> to select analogue manual Scan and press oK or to enter. E Channel Skip Channel skip allows you to skip one or more channels when pressing p <> on the remote control to switch between channels. Menu Picture Sound TV Features Parental Eco Start Frequency (MHz) 45. 00 Search for analogue channels 1 Press menu on the remote control and select tV Channels note Scan Up Scan Down · You are prompted to enter current password to enter Channels if Channel Block /parental Guidance / input Block in the parental menu is not the default setting. EXIT Back 2 3 4 5 Press <> to select Channel Skip and press oK or to enter the channel list. Follow the on-screen instructions to exit. 3 4 5 6 In the Start Frequency (mHz) box, enter the frequency by using the digit buttons on the remote control. Press <> to select Scan up or Scan Down to scan the next available analogue channel from the frequency you have entered. When complete, follow the on-screen instructions to exit. note: · To watch the skipped channels, enter the channel numbers by using the digit buttons on the remote control or select from pr liSt. E Channel Sort Channel sort allows you to reorder the channels in the pr liSt. E Favourite network Select When watching the digital TV, select your favourite network in order to allocate channels of your favourite network on the top of channel list (PR LIST). 1 Press menu on the remote control and select tV Channels 1 Press menu on the remote control and select tV Channels note note · You are prompted to enter current password to enter Channels if Channel Block /parental Guidance / input Block in the parental menu is not the default setting. · You are prompted to enter current password to enter Channels if Channel Block /parental Guidance / input Block in the parental menu is not the default setting. 2 3 4 5 6 Press <> to select Channel Sort and press oK or to enter the channel list. Follow the on-screen instructions to exit. 2 3 4 Press <> to select Favorite network Select and press oK or to enter the network list. Follow the on-screen instructions to exit. note · This menu is available only when 1) "Norway" is selected on country setting and 2) more than two networks are found after automatic channel scan. 15 tV menu E Channel edit Channel edit allows you to change the channel number or the channel name. 1 Press menu on the remote control and select tV Channels note 1 Press menu on the remote control and select tV Channels note · You are prompted to enter current password to enter Channels if Channel Block /parental Guidance / input Block in the parental menu is not the default setting. · You are prompted to enter current password to enter Channels if Channel Block /parental Guidance / input Block in the parental menu is not the default setting. 2 3 4 5 Press <> to select Decoder and press oK or to enter available analogue channel list. Follow the on-screen instructions to exit. 2 3 4 5 Press <> to select Channel edit and press oK or to enter the channel list. Press <> to highlight one of the following: · Channel number: Enter a new channel number by using the digit buttons on the remote control · Channel name: Press the digit buttons on the remote control to rename the channel. (Press each button repeatedly to change between characters. ) E analogue Ch Fine tune You can manually fine tune analogue channels when reception is poor. 1 Press menu on the remote control and select tV Channels. note · You are prompted to enter current password to enter Channels if Channel Block / parental Guidance / input Block in the parental menu is not the default setting. 0-9 digit buttons with available characters 2 3 Press <> to select analogue Ch Fine tune and press oK or to enter the analogue channel list. Follow the on-screen instructions to exit. ABC1 JKL4 STU7 DEF2 MNO5 VWX8 +-. 0 GHI3 PQR6 YZ9 4 5 6 · Frequency: Use digit buttons on the remote control to enter the frequency. (Only for analogue channels) · Sound System: Press to select the sound system. (Only for analogue channels) E Clean Channel list Select to clean all the channels that stored in the channel list. 1 Press menu on the remote control and select tV Channels note 6 Follow the on-screen instructions to exit. note · The new channel number you have entered can not override the exist one. · You are prompted to enter current password to enter Channels if Channel Block /parental Guidance / input Block in the parental menu is not the default setting. 2 3 E assign a channel decoder (For atV) Decoders that decode channels can be connected to SCART. Before selecting channels, make sure your TV is connected to SCART. Press <> to select Clean Channel list and press oK or to enter. Select oK and press oK on the remote control to clean channel list. 16 tV menu Features Select menu language Select the menu display language. note · Constant use of the normal picture format can cause screen distortion. Zoom 1 (not for HD) Scales the classic 4:3 format to 14:9. 1 2 3 Press menu on your remote control and select Features menu language. Follow the on-screen instructions to exit. 4:3 mode Select aspect ratio behavior for Auto mode. When 4:3 is selected, the picture size will follow WSS or Scart Pin8 Spec. If 16:9 is selected, the picture format will change to wide screen. Zoom 2 (not for HD) Scales the classic 4:3 format to 16:9. 1 2 3 Press menu on your remote control and select Features 4:3 mode. [. . . ] · ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. Visit www. divx. com for more information and software tools to convert your files into DivX video. · ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play DivX Video-on-Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu. [. . . ]