User manual SHARP JX-9600/PS

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP JX-9600/PS. We hope that this SHARP JX-9600/PS user guide will be useful to you.


SHARP JX-9600/PS : Download the complete user guide (2490 Ko)

You may also download the following manuals related to this product:

   SHARP JX-9600/PS (2695 ko)

Manual abstract: user guide SHARP JX-9600/PS

Detailed instructions for use are in the User's Guide.

[. . . ] 15 seconds Horizontal: 8 pels/mm Vertical: Standard: 3. 85 lines/mm Fine /Halftone: 7. 7 lines/mm Super fine: 15. 4 lines/mm 5 pages max. (A4, 80 g/m2 paper) Thermal recording 64 levels MR, MH, H2 Automatic document feeder Recording system Halftone (grayscale) Compression scheme *Based on Sharp Standard No. 1 Chart at standard resolution is Sharp special mode, excluding time for protocol signals (i. e. , ITU-T phase C time only). 1 Display 16-digit LCD display Applicable telephone line Public switched telephone network Compatibility Input document size ITU-T (CCITT) G3 mode Automatic feeding: Width: 148 to 210 mm Length: 140 to 297 mm Manual feeding: Width: 148 to 210 mm Length: 140 to 600 mm 210 mm max. mode is for connecting an answering machine) Yes Yes (cannot be used if power fails) 220 - 240 V AC, 50/60 Hz 5 - 35°C 30 - 85% RH Standby: 4. 0 W Maximum: 115 W Width: 304 mm Depth: 236mm Height: 122 mm Approx. 2. 6 kg Effective scanning width Effective printing width Contrast control Reception modes Copy function Telephone function Power requirements Operating temperature Humidity Power consumption Dimensions Weight As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. [. . . ] If you don't answer within this time, your fax will send a fax tone to the other machine to allow the calling party to send a fax manually if they desire. Note: Only the fax will alert you to voice calls or manually dialled faxes by pseudo ringing. An extension phone connected to the same line will not ring after the connection has been established. 38 Using A. M. mode, press A. M. RESOLUTION/ RECEPTION MODE TEL FAX RESOLUTION/ RECEPTION MODE until the arrow in the display points to In A. M. mode, your fax will automatically receive voice and fax messages if you have connected an answering machine to the fax machine. See Chapter 6 for more details. Using FAX Mode To select FAX mode, press RESOLUTION/ RECEPTION MODE until RESOLUTION/ RECEPTION MODE the arrow in the display points to FAX. TEL FAX TEL/FAX A. M. When the reception mode is set to FAX, the fax machine will automatically answer all calls on two rings and receive incoming faxes. 2 rings Fax reception If you pick up the handset before the machine answers, you can talk to the other party and/or receive a fax as explained in Using TEL Mode on page 41. 39 3. Receiving Faxes TEL/FAX A. M. Using FAX Mode Changing the number of rings If desired, you can change the number of rings on which the fax machine answers incoming calls in FAX and TEL/FAX mode. Any number from 2 to 5 can be selected. Note for Singapore: "2" or "3" can be selected for the number of rings. 1 2 3 Display: Press FUNCTION once and 4 once. OPTION SETTING Press once. NUMBER OF RINGS Enter the desired number of rings (any number from 2 to 5). Example: 3 rings 3 4 STOP Press to return to the date and time display. 40 Using TEL Mode Using TEL Mode When the reception mode is set to TEL, you must answer all calls by picking up the fax machine's handset or an extension phone connected to the same line. To select TEL mode, press RESOLUTION/ RECEPTION MODE until the arrow in the RESOLUTION/ RECEPTION MODE TEL FAX TEL/FAX A. M. Answering with the fax's handset 1 When the fax machine rings, pick up the handset. 2 If you hear a fax tone, wait until the display shows RECEIVING and then replace the handset. Beep RECEIVING Note: If you have set the Fax Signal Receive setting (page 43) to NO, press START to begin reception. 3 If the other party first speaks with you and then wants to send a fax, press START START RECEIVING after speaking. Answering Machine Connection Connecting an Answering Machine If desired, you can connect an answering machine to your fax machine's TEL. This will allow you to receive both voice messages and faxes when you are out. Important: If the answering machine is not connected to the TEL. SET socket on the fax as shown, the setup will not operate properly. 1 Remove the seal covering the TEL. SET socket. 2 Connect the answering machine's telephone line plug to the TEL. NE To answering machine's telephone line socket. 48 Using the Answering Machine Connection Changing the outgoing message The outgoing message (OGM) of your answering machine should be changed to inform callers who want to send a fax to press their Start key. Please leave a message after the beep or press your facsimile Start key to send a fax. Thank you for calling. " It is advisable to keep the length of the message under 10 seconds. If it is too long, you may have difficulty receiving faxes sent by automatic dialling. If your outgoing message must be longer than 10 seconds, leave a pause of about four seconds at the beginning of the message. This will give your fax a chance to detect fax tones sent when automatic dialling is used. Using the Answering Machine Connection 1 Set the reception mode to A. M. RESOLUTION/ RECEPTION MODE TEL FAX TEL/FAX A. M. 2 Set your answering machine to auto answer. Your answering machine must be set to answer on a maximum of two rings. If not, you may not be able to receive faxes sent by automatic dialling. If your answering machine has a toll saver function, make sure that it will answer by the fourth ring. Note: If your answering machine has a remote retrieval function, make sure the code used to activate remote retrieval is different from the code used to activate fax reception with an extension telephone (see Chapter 3, Receiving Faxes). If they are the same, entering the code from an outside telephone to retrieve messages will cause the fax machine to be activated. 49 6. [. . . ] The HOLD/SEARCH key has been pressed to put the other party on hold during a phone conversation. This appears if you attempt to send a fax by automatic dialling and the line is busy or the receiving fax machine doesn't answer. This may occur during fax reception if too much data is received before the pages can be printed out. If faxes have been received to memory because printing is not possible, resolve the problem so that printing can continue, see Substitute Reception to Memory on page 44. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP JX-9600/PS




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP JX-9600/PS will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.