User manual SHARP EL-9200/9300
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP EL-9200/9300. We hope that this SHARP EL-9200/9300 user guide will be useful to you.
You may also download the following manuals related to this product:
SHARP EL-9200/9300 (5507 ko)
SHARP EL-9200/9300 (4626 ko)
SHARP EL-9200/9300 (5074 ko)
SHARP EL-9200/9300 OPERATION MANUAL (5074 ko)
SHARP EL-9200/9300 OPERATION MANUAL (4626 ko)
Manual abstract: user guide SHARP EL-9200/9300
Detailed instructions for use are in the User's Guide.
[. . . ] 12
· · Note of calculation accuracy · In principle, the calculation error is ±1 of the last digit (in case of exponential display, the calculation error is · ·
with clean water and immediately consult a doctor. Should fluid from a leaking battery come into contact with your skin or clothes, immediately wash with clean water. If the product is not to be used for some time, to avoid damage to the unit from leaking batteries, remove them and store in a safe place. Do not fit partially used batteries, and be sure not to mix different batteries types.
; ® 1®; Ï Ï 1® ; 1 ®; ® Ï
FRAC (Simplified by 2, the lowest common factor of 12 and 6. )
FRAC (Simplified by 3, the lowest common factor of 6 and 3. )
FRAC 6 (Manually specify 6, the Greatest Common Factor of 12 and 6, to simplify the fraction. )
Notes: · If the wrong number is specified for a common factor, an error will occur. [. . . ] (For example, calculation of sinh x or tanh x at x = 0).
[2a b/c] Converts an improper fraction to a mixed number. <Example>
·
Change
INTRODUCTION
Congratulations on purchasing the EL-9200/9300 Graphing Calculator. See the enclosed EL-9400 operation manual for almost all the operations. This supplement describes about the features added from the EL-9400, such as fraction calculations (Manual Calculations), pie chart (Statistics), and int÷/remain functions (Manual Calculations). It also describes the feature updates, such as capability of a self-made Slide Show, random function, commands for programming. Read both the EL-9400 Operation Manual (where EL-9400 and CE-LK1 should be read as EL-9200/9300 and CE-LK1P respectively) and this supplement before operation. Please store both the manual and the supplement in a convenient location for your reference.
12
;
12 to a mixed number. 5
5 >Ï FRAC
2®
[3 b/c] Converts a mixed number to an improper fraction. <Example>
·
Ï 3®
Change 2
FRAC FRAC
2 5 to an improper fraction.
THE NEW KEYS FOR EL-9200/9300
EL-9200/9300
[4A. xxx] Converts a fraction to a decimal number. <Example>
·
Ï 4®
Change
12 to a decimal number. 5
Integer Division
INT
÷
Performs an integer division, and returns a quotient and a remainder. : Put a title on the slide show.
2
MBox·
MBox ·
: Input a title. ®
C®
·
: After creating an original slide show, press to store the original slide show. (When another slide show is created following the original slide show, the previous data is cleared and updated by the new slide show. )
Register screens.
Ï
3
MBox+
4
MBox
<Example> Input "Y1 = 2X5" and "Y2 = X2", and then store the equations, graph screen, table screen, and graph and table screen in sequential order. Press
The message, "STORE SCREEN:01", will appear instantaneously.
6. Press
Draws graphs for "Y1 = 2X 5" and "Y2 = X2".
The message, "STORE SCREEN:02", will appear instantaneously.
¬. MBox + The lines on either side is (Q3Q1) x 1. 5 Uses "+" to draw data points (including Xmin and Xmax) of the lines that are on the outside Specifies modified box plot. MBox The lines on either side is (Q3Q1) x 1. 5 Uses " " to draw data points (including Xmin and Xmax) of the lines that are on the outside
EL-9200/9300 functions (P220) MajorSubMinorName category category category STAT GRAPH F PIE 1 2 Pie Pie%
Description
Example of use
Draws a pie graph using Pie entered values. Draws a pie graph using the Pie% percentage
Repeat the above steps to register the necessary screens. Subsequently, normal operations can be performed unless and If an original Slide Show has been already stored, the delete confirmation display appears after selecting [C NEW]. Press Press
®oe Ï
Ï
EL-9200/9300 functions (P223) MajorSubMinorName category category category SLIDE B ORG SHOW C NEW D EDIT 1 2 3 MOVE DEL RENAME
Description Displays the title and the number of screens of the currently editing Slide Show. Delete the pages Rename the title of the slide show.
Example of use
to delete the previous Slide Show file. Viewing the Original Slide Show
To view the original slide show which was created previously, follow these steps. [. . . ] ®.
SETUP menu
(Same as the EL-9400)
H SIMPLE Auto Manual
P 225
MATH menu
(Same as the EL-9400. )
P 226
3. Editing the Original Slide Show
The registered slide show data can be sorted, and deleted, and the title can be renamed in the edit mode.
(1) Changing the order of the screens (MOVE)
1. Press or to select the place you wish to move to and press
* Exit this mode by pressing
D 1. ®.
to delete.
(2) Deleting the registered screen (DEL)
To delete screen. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP EL-9200/9300
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP EL-9200/9300 will begin.