User manual SHARP CMS/CP-150/CDH

[. . . ] When the ON/ STAND-BY button is set at STAND-BY position, the unit may be brought into operation by the timer mode or remote control. This unit contains dangerous voltages, always remove mains plug from the socket before any service operation and when not in use for a long period. To prevent fire or shock hazard, do not expose this appliance to dripping or splashing. [. . . ] No objects filled with liquids, such as vases, should be placed on the apparatus. CAUTION This product is classified as a CLASS 1 LASER product. Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the cabinet. Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. 0. 6 mW z z z Note: Audio-visual material may consist of copyrighted works which must not be recorded without the authority of the owner of the copyright. Please refer to the relevant laws in your country. 02/5/27 CMS/CP-150/CDH(X)E1. fm Accessories Please confirm that the following accessories are included. CMS/CP-150/CDH ENGLISH Remote control 1 "AA" size battery (UM/SUM-3, R6, HP-7 or similar) 2 AM loop aerial 1 AA FM aerial 1 AA AC power lead 1 General Information Note: Only the above accessories are included. Contents Page General Information Page Precautions . . 4 - 6 Tape Playback Karaoke Tape Recording Advanced Features References Listening to a cassette tape . 19, 20 Basic Operation CD Playback Radio Listening to a CD (CDs) . Please keep it (see page 27). Aerial connection Supplied FM aerial: Supplied AM loop aerial: Connect the AM loop aerial to the AM LOOP socket. Place the AM loop aerial on a shelf, etc. , or attach it to a stand or a wall with screws (not supplied). Preparation for Use Connect the FM aerial wire to the FM 75 OHMS terminal and position the FM aerial wire in the direction where the strongest signal can be received. Note: Placing the aerial on the unit or near the AC power lead may cause noise pickup. Place the aerial away from the unit for better reception. < Attaching to the wall > Wall External FM aerial: Screws (not supplied) Use an external FM aerial if you require better reception. Consult your dealer. External FM aerial 75 ohm coaxial cable Note: When an external FM aerial is used, disconnect the supplied FM aerial wire. z Installing the AM loop aerial: < Assembling > Caution: Use speakers with an impedance of 8 ohms or more, as lower impedance speakers can damage the unit. The right speaker is the one on the right side when you face the unit. Do not allow any objects to fall into or to be placed in the bass reflex ducts. You may be in- Incorrect jured. - System connections - T z z z z z z Removing the transport screw Speaker connection Right speaker Left speaker T T Connect the wire with the white line to the minus (-) terminal and the plain wire to the plus (+) terminal. 4 Notes: The speaker grilles are not removable. There is no physical distinction between the right and left speakers. E-8 02/5/27 CMS/CP-150/CDH(X)E1. fm CMS/CP-150/CDH System connections (continued) Setting the AC voltage selector ENGLISH Preparation for Use - System connections - E-9 T T z z Check the setting of the AC voltage selector located on the rear panel before plugging the unit into a wall socket. [. . . ] You may be in- Incorrect jured. - System connections - T z z z z z z Removing the transport screw Speaker connection Right speaker Left speaker T T Connect the wire with the white line to the minus (-) terminal and the plain wire to the plus (+) terminal. 4 Notes: The speaker grilles are not removable. There is no physical distinction between the right and left speakers. E-8 02/5/27 CMS/CP-150/CDH(X)E1. fm CMS/CP-150/CDH System connections (continued) Setting the AC voltage selector ENGLISH Preparation for Use - System connections - E-9 T T z z Check the setting of the AC voltage selector located on the rear panel before plugging the unit into a wall socket. For 100 kHz FM interval (10 kHz in AM) 100/10 For 50 kHz FM interval (9 kHz in AM) 50/9 3 Whilst pressing down the TUNER (BAND) button and the DISC SKIP button, press the ON/STAND-BY button until "CLEAR" appears. To turn the power on - System connections - T Setting the FM/AM span selector Demonstration mode z z T The first time the unit is plugged in, the unit will enter the demonstration mode. [. . . ]