User manual SHARP CDE250 OPERATION MANUAL

[. . . ] To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. MINI COMPONENT SYSTEM MODEL CD-E250E Mini Component System consisting of CD-E250E (main unit), CP-E250E (front speakers) and GBOXS5001SJB1 (surround speakers). CD-E250E OPERATION MANUAL If you require any advice or assistance regarding your Sharp product, please visit our web-site www. sharp. co. uk/customersupport. Customers without Internet access may telephone 08705 274277 during office hours (or (01) 676 0648 if telephoning from Ireland). 0301 Accessories Please confirm that the following accessories are included. Remote control × 1 FM/AM loop aerial × 1 AC power lead × 1 Note: Only the above accessories are included. CDE250EE_FRONT. pm 1 03. 2. 17, 3:34 PM CD-E250E Special notes NOTES FOR USERS IN THE U. K. AND IRELAND The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. [. . . ] When the DISC SKIP button is pressed during playback, the next disc will begin automatically. When one of the 1 - 3 buttons on the remote control is pressed during playback, the selected disc will begin automatically. It is possible to enter a track number which is larger than the total track number of the disc (maximum 99). In this case, the last track on the disc will be played back. To repeat a desired track: Perform steps 1 - 4 in the "Programmed play" section on page 18 and then press the / button twice. Caution: After performing repeat play, be sure to press the wise, the disc(s) will play continuously. Other- " Random play The tracks on the disc(s) can be played in random order automatically. Press the RANDOM button on the remote control to begin random play. To cancel random play: Press the button. 17 03/2/17 CD-E250E(E)2. fm CD Playback Selected track number Press the / button to start playback. When the end of the last track is reached, the next disc will automatically be started. All tracks on up to 3 discs, or a programmed sequence can be continuously repeated. CD-E250E Advanced CD playback (continued) " Programmed play You can choose up to 32 selections for playback in the order you like. To clear the programmed selections: Whilst the "MEMORY" indicator is lit, set the CD to the stop mode and then press the CLEAR button. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original programme. Even if you press the ON/STAND-BY button to enter the stand-by mode or change the function from CD to another, the programmed selections will not be cleared. During programme operation, random play is not possible. 1 Whilst in the stop mode, press one of the 1 - 3 buttons on the remote control to select the desired disc. Press the or button to select the desired track. Selected disc number 2 Selected track number CD Playback 3 Press the MEMORY/SET (MEMORY) button to save the track number. Playback order When the track is memorised, "MEMORY" will appear. " Care of compact discs Compact discs are fairly resistant to damage, however mistracking can occur due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your CD collection and player. Do not write on either side of the disc, particularly the non-label side from which signals are read. Keep your discs away from direct sunlight, heat, and excessive moisture. Fingerprints, dirt, or water on the CDs can cause noise or mistracking. If a CD is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the centre, along the radius. NO YES Correct 4 Repeat steps 1 - 3 for other tracks. If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR button. Press the / button to start playback. 5 18 03/2/17 CD-E250E(E)2. fm Listening to the radio " Tuning CD-E250E 1 2 3 Press the ON/STAND-BY button to turn the power on. [. . . ] Demagnetise these parts once every 30 hours of playing/recording time by using a commercial tape head demagnetiser. Cleaning the CD pickup lens Poor performance during CD playback (skipping or jumping) can be caused by a dirty or contaminated CD laser pick up lens. If this happens then the use of a commercially available CD lens cleaning discs may restore normal operation. Contact your supplier or local CD software dealer to obtain CD lens cleaning discs. [. . . ]