User manual SHARP CD-PC651H

[. . . ] It will guide you in operating your SHARP product. Special Notes Important Instruction CAUTION - Introduction / Special Notes - Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. 0. 6 mW z This Mini Component System is classified as a CLASS 1 LASER product. z Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the cabinet. [. . . ] z You can skip to any track by pressing the PRESET button repeatedly until the desired track number appears. z You can skip to any track by pressing the PRESET button repeatedly until the desired track number appears. - Listening to a CD (CDs) - z Playback will begin from track 1 on the disc you have selected to play. After that disc finishes playing, the next disc will automatically start playback. z When the last track on the third disc has finished playing, the CD player will stop automatically. z When there is no CD in one of the disc 1 - 3 positions, that position will be skipped and the next CD will be played. To restart the track being played: Press the PRESET CD Playback To interrupt playback: Press the button on the remote control. To resume playback from the same point, press the button. Notes: z You can locate the beginning of a track on a single disc only. z The PRESET / or PRESET / button on the remote control allows you to locate the beginning of a track. To stop playback: Press the button. , , To locate the desired portion For audible fast forward: Press and hold down the PRESET button during playback. To remove the CDs: Whilst in the stop mode, press the OPEN/CLOSE button. Then, press the DISC SKIP button to rotate the disc tray and remove the remaining disc. After use: Press the ON/STAND-BY button to enter the power stand-by mode. For audible fast reverse: Press and hold down the PRESET button during playback. Caution: z z z z z Do not place two CDs in one disc tray. If the power fails whilst the tray is open, wait until the power is restored. If the disc tray is stopped forcibly, "ER-CD10" will appear in the display and the unit will not function. If this occurs, press the ON/STAND-BY button to enter the power stand-by mode and then turn the power on again. Manual tuning: or ) button to tune in to the desired Press the TUNING/TIME button as many times as required to tune in to the desired station. Auto tuning: z When radio interference occurs, auto scan tuning may stop automatically at that point. z To stop the auto tuning, press the TUNING/TIME button again. To receive an FM stereo transmission: Press the TUNER (BAND) button to display the "ST" indicator. FM stereo mode indicator FM stereo receiving indicator z If the FM reception is weak, press the TUNER (BAND) button to extinguish the "ST" indicator. The reception changes to monaural, and the sound becomes clearer. After use: Press the ON/STAND-BY button to enter the power stand-by mode. Sound Control (See page 14. ) ENGLISH E-20 Radio Notes: - Listening to the Radio - When the TUNING/TIME button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Listening to the Memorised Station , , Memorising a station You can store 40 AM and FM stations in memory and recall them at the push of a button. (Preset tuning) , , To recall a memorised station Press the PRESET or PRESET 0. 5 seconds to select the desired station. button for less than 1 2 - Listening to the Memorised Station - Perform the steps 1 - 3 in "Listening to the Radio" on page 20. Press the MEMORY/SET button to enter the preset tuning saving mode. Preset channel This can be operated by pressing the button on the remote control. Frequency and frequency band PRESET / or PRESET / 3 Within 30 seconds, press the PRESET button to select the preset channel number. or PRESET , , To scan the preset stations The stations saved in memory can be scanned automatically. (Preset memory scan) Radio 1 Store the stations in memory, in order, starting with preset channel 1. Press the PRESET than 0. 5 seconds. or PRESET button for more 4 Within 30 seconds, press the MEMORY/SET button to store that station in memory. z The preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each. z This can be operated by pressing the PRESET / or PRESET / button on the remote control. 2 Press the PRESET or the desired station is located. PRESET button again when , , To erase entire preset memory If the "MEMORY" and preset number indicators go out before the station is memorised, repeat the operation from step 2. 1 2 5 Repeat steps 1 - 4 to set other stations, or to change a preset station. When a new station is stored in memory, the station previously memorised will be erased. Press the ON/STAND-BY button to enter the stand-by mode. [. . . ] However, another unit will not be turned on or off. Listening to the Radio (See page 20. ) ENGLISH E-30 - Timer and Sleep Operation - Whilst the sleep time is displayed, press the TUNING/TIME ( or ) button. Advanced Features To change the sleep time: Enhancing Your System The connection lead is not included. Purchase a commercially available lead as shown below. , , Listening to the playback sounds from VCR, DVD, etc. to the VIDEO/ AUX sockets. When using video equipment, connect the audio output to this unit and the video output to a television. VCR, DVD, etc. To the line output sockets Advanced Features White Red 2 3 4 Press the ON/STAND-BY button to turn the power on. Play the connected equipment. - Enhancing Your System - Note: To prevent hum interference, place this unit away from a television. Red White , , To record on a tape RCA lead (not supplied) 1 2 3 4 5 Insert a cassette in the TAPE 2 cassette compartment. [. . . ]