User manual SHARP CD-CH1000H

[. . . ] It will guide you in operating your SHARP product. Contents Important Instruction !20 E-1 ENGLISH 01/1/25 E1. fm Special Notes CAUTION Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. STIRRA EJ IN I STRALEN OCH BETRAKTA EJ STRALEN MED OPTISKA INSTRUMENT. ALA TUIJOTA SATEESEEN ALAKA KATSO SITA OPTISEN LAITTEEN LAPI. " This Audio Tower System is classified as a CLASS 1 LASER product. [. . . ] Turn the jog dial to select "CLOCK" and within 10 seconds, press the ENTER button. To confirm the time display: [When the unit is in the stand-by mode] Press the DISPLAY button on the remote control. Note: "CLOCK" will appear or time will flash at the push of the DISPLAY button when the AC power supply is restored after a power failure or unplugging the unit. To reset the clock: [When time is flashing] 1 Press the ON/STAND-BY button. [When "CLOCK" appears] Perform "Setting the Clock" from the beginning. To change the 24-hour or 12-hour display: 1 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on page 32 for details. ] 2 Perform "Setting the Clock" from the beginning. 4 Turn the jog dial to select the 24-hour or 12-hour display and within 2 minutes, press the ENTER button. "0:00" "AM 12:00" "AM 0:00" The 24-hour display will appear. (AM 0:00 - PM 11:59) Note that this can only be set when the unit is first installed or it has been reset. [Refer to "Clearing all the memory (reset)" on page 32 for details. ] ENGLISH E-16 01/1/25 E2. fm -Setting the Clock- " The hour will not advance even if minutes advance from "59" to "00". (Seconds are not displayed. ) The time display will disappear after a few seconds. Basic Operation Listening to a CD (CDs) This system can play audio CD-R and CD-RW discs just as CD discs, but cannot perform recording. 5 Press the DISC 1 button to close the disc tray 1. Means "disc inside" Total number of tracks Total playing time -Listening to a CD (CDs)- CD Playback 6 You can place discs on the trays 2 - 6 by following steps 3 - 5. Note: The system will search CD trays until it finds a CD and will not search the rest of trays. 7 !To play discs in turn (from Disc 1 to Disc 6) 1 Press the ON/STAND-BY button to turn the power on. 4 Place a CD on the disc tray 1, label side up. " Be sure to place 8 cm (3") CD in the middle of the disc trays. The remaining playing time for the current track will be displayed. Normal playback mode 2 Press the or one of the DISC 1 - DISC 6 buttons to start playback. " If playback is started by pressing the button, repeat or random play will be performed on all discs. " If playback is started by pressing one of the DISC 1 - DISC 6 buttons, repeat or random play will be performed on that disc. To repeat a programmed sequence: Perform steps 1 - 6 in the "Programmed Play" section, select the repeat playback and then press the button. Notes: " After performing repeat or random play, be sure to press the button. " In random play, the CD player will select and play tracks automatically. (You cannot select the order of the tracks. ) To cancel repeat or random play: Press the PLAY MODE button repeatedly to select the normal play mode. The total remaining playing time for the disc will be displayed. Notes: " During random play, the total remaining playing time will not be displayed. " Depending on the CD, the playing time display may not match the total playing time which is indicated on the CD jacket, as the time between tracks is not included. E-19 ENGLISH 01/1/25 E2. fm Programmed Play By specifying discs from 1 to 6, and tracks from 1 to 99, you can choose up to 32 selections for playback in the order you like. 1 6 7 Press the Press the button. button to start playback. When in the stop mode, press the MEMORY button. " At this time, playback will not begin even if one of the DISC 1 - DISC 6 buttons is pressed. 2 Press one of the DISC 1 - DISC 6 buttons to select the desired disc. Selected disc number To cancel the programmed play mode: Whilst in the stop mode, press the CLEAR button. The MEMORY indicator will disappear and all the programmed content will be cleared. Advanced CD Playback To clear the programmed selections: Press the CLEAR button whilst the "MEMORY" indicator is flashing. Each time the button is pressed, one track will be cleared, beginning with the last track programmed. 3 Turn the jog dial to select the desired track. Adding tracks to the programme: If a programme has been previously stored, the "MEMORY" indicator will be displayed. The new tracks will be stored after the last track of the original programme. [. . . ] " Playback sounds are skipped, or stopped in the middle of a track. Condensation Sudden temperature changes, storage or operation in an extremely humid environment may cause condensation inside the cabinet (CD pickup, tape heads, etc. ) or on the transmitter LED on the remote control. If this happens, leave the power on with no disc (or cassette) in the unit until normal playback is possible (about 1 hour). Wipe off any condensation on the transmitter LED with a soft cloth before operating the unit. ! [. . . ]