User manual SHARP CD-C607H

[. . . ] Wenn die ON/STAND-BY-Taste auf STAND-BY eingestellt wird, kann das Gert unter Verwendung der Timer-Betriebsart oder Fernbedienung in Betrieb gesetzt werden. Warnung: In diesem Gert sind keine vom Benutzer wartbaren Teile vorhanden. Vor Ausfhrung von irgendwelchen Kundendienstarbeiten oder bei lngerer Nichtverwendung des Gertes stets den Netzstecker aus der Netzsteckdose ziehen. Lorsque la touche ON/STAND-BY est mise en STAND-BY, l'appareil est toujours sous tension. [. . . ] This unit should only be used within the range of 5C 35C (41F - 95F). The apparatus is designed for use in moderate climates. The sound level at a given volume setting depends on speaker efficiency, location and various other factors. Excessive sound pressure from earphones and headphones can cause hearing loss. E-2 Controls and indicators 1 Front panel 2 MINI COMPONENT SYSTEM CD-DH790 3 4 5 FUNCTION ON/STAND-BY 9 10 11 12 13 PUSH OPEN VOL AUDIO IN 6 7 8 14 PHONES Page 1. 15 1 2 3 4 5 6 7 8 9 10 Display 16 17 11 18 19 12 1314 15 Page 1. 10 E-3 Controls and indicators (continued) 1 24 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Remote control CD USB 25 26 27 28 29 30 31 32 33 34 TAPE 35 36 37 38 39 Page 1. Speaker Wire 1 2 3 4 E-4 System connections Make sure to unplug the AC power lead before making any connections. TV AM loop aerial Installing the AM loop aerial < Assembling > To video input socket Video cable (not supplied) < Attaching to the wall > wall screws (not supplied) FM aerial Right speaker Left speaker Red Black Wall socket (AC 220 - 240 V ~ 50/60 Hz) Aerial connection Demonstration mode Supplied FM aerial: Connect the FM aerial wire to the FM 75 OHMS socket and position the FM aerial wire in the direction where the strongest signal can be received. External FM aerial: Use an external FM aerial (75 ohms coaxial cable) for better reception. When an external FM aerial is used, disconnect the supplied FM aerial wire. Supplied AM loop aerial: Connect the AM loop aerial to the AM and GND terminals. Place the AM loop aerial on a shelf, etc. , or attach it to a stand or a wall with screws (not supplied). Keep the remote control away from moisture, heat, shock, and vibrations. To turn the power on Press the ON/STAND-BY button to turn the power on. After use: Press the ON/STAND-BY button to enter the power stand-by mode. Display brightness control To dim the display brightness, hold down the CLEAR/ DIMMER button on the remote control for 2 seconds or more. Volume auto fade-in If you turn off and on the main unit with the volume set to 27 or higher, the volume starts at 16 and fades in to the last set level. Volume control Turn the volume knob towards VOL +/ (on main unit) or press VOLUME +/ (on remote control) to increase or decrease the volume. X-Bass control Test of the remote control Check the remote control after checking all the connections. The remote control can be used within the range shown below: Remote sensor MINI COMPONENT SYSTEM CD-DH790 When the power is first turned on, the unit will enter the extra bass mode which emphasises the bass frequencies, and "X-BASS" will appear. To cancel the extra bass mode, press the X-BASS button on the remote control. Bass control 1 Press the BASS/TREBLE button to select "BASS". 2 Within 5 seconds, press the VOLUME (+ or ) button to adjust the bass. Treble control 1 Press the BASS/TREBLE button to select "TREBLE". 2 Within 5 seconds, press the VOLUME (+ or ) button to FUNCTION ON/STAND-BY adjust the treble. 0. 2 m - 6 m (8" - 20') AUDIO IN PHONES VOL PUSH OPEN Equaliser When the EQUALIZER MODE button is pressed, the current mode setting will be displayed. To change to a different mode, press the EQUALIZER MODE button repeatedly until the desired sound mode appears. FLAT GAME No equalization. CLASSIC For classical music. POPS VOCAL E-6 JAZZ Setting the clock (Remote control only) Listening to the iPod Supported iPod models: iPod nano (software 1. 2 above) iPod mini (software 1. 2 above) iPod (5th generation) (software 1. 3 above) (Dock connector equipped Click Wheel model) iPod (4th generation) (software 3. 0. 2 above) (Dock connector equipped Click Wheel model) iPod nano (2nd generation) (software 1. 0. 0 above) iPod nano (3rd generation) (software 1. 0. 3 above) iPod nano (4th generation) (software 1. 0. 3 above) iPod classic (software 1. 0. 3 above) iPod touch (software 1. 1 above) iPod touch (2nd generation) (software 2. 1 above) Caution: Please update your iPod unit to the latest software version from Apple's homepage before using it. Notes: Once the iPod is connected to the unit it will begin charging. The iPod unit cannot be charged whilst the main unit is in the stand-by mode or during USB mode. Auto power on function: When you press any of the following buttons, the unit turns on. [. . . ] Excessive sound pressure from earphones and headphones can cause hearing loss. Be sure your headphones have a 3. 5 mm (1/8") diameter plug and impedance between 16 and 50 ohms. Adjust the volume using the VOLUME control. Symptom Sound skipping. If a power failure occurs during playback, the heads remain engaged with the tape. [. . . ]