User manual SHARP CD-C470H

[. . . ] It will guide you in operating your SHARP product. Special Notes Important Instruction CAUTION - Introduction / Special Notes - Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. 0. 6 mW z This Mini Component System is classified as a CLASS 1 LASER product. z Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. As the laser beam used in this compact disc player is harmful to the eyes, do not attempt to disassemble the cabinet. [. . . ] [Refer to "Clearing all the memory (reset)" on page 31 for details. ] Perform "Setting the Clock" from the beginning. E-13 ENGLISH Listening to a CD (CDs) This system can play audio CD-R and CD-RW discs just as CD discs, but cannot perform recording. (However, some CD-R and CD-RW discs may not be played. ) , , To play discs in turn (from Disc 1 to Disc 6) 1 2 3 4 Press the ON/STAND-BY button to turn the power on. Press the 1 button to open the disc tray 1. Place the CD on the disc tray 1, label side up. Be sure to place 8 cm (3") CD in the middle of the disc trays. 12 cm (5") 8 cm (3") 5 Press the 1 button to close the disc tray 1. Total number of tracks Total playing time Music schedule Means "disc inside" The music schedule will display only the number of tracks on the disc. If the CD contains more than 15 tracks, " " will appear. 6 You can place discs on the trays 2 - 6 by following steps 3 - 5. Note: The system will search CD trays until it finds a CD and will not search the rest of the trays. Continued to the next page Sound Control (See page 12. ) ENGLISH E-14 - Listening to a CD (CDs) - CD Playback Listening to a CD (CDs) (continued) 7 Press the ( ) button to start playback. , , To locate the beginning of a track To move to the beginning of the next track: Press the / button for less than 0. 5 seconds during playback. z You can skip to any track by pressing the / button repeatedly until the desired track number appears. z Playback will begin from track 1 on the DISC 1. After that disc finishes playing, the next disc will automatically play. z When the last track on the DISC 6 has finished playing, the CD player will stop automatically. To restart the track being played: Press the / button for less than 0. 5 seconds during playback. z You can skip to any track by pressing the / button repeatedly until the desired track number appears. - Listening to a CD (CDs) - CD Playback z When there is no CD in one of the disc tray 1 - 6 positions, that position will be skipped and the next CD will be played. To interrupt playback: Press the button on the remote control. To resume playback from the same point, press the button. Note: You can locate the beginning of a track on a single disc only. To stop playback: Press the button. , , To locate the desired portion For audible fast forward: 6 and exchange discs. 1 to To exchange other CDs whilst playing a disc: Press CD eject button for any stopped CD from To remove the CDs: Whilst in the stop mode, press the CD eject button for any CD from remove the disc. Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). Manual tuning: or ) button to tune in to the desired Press the TUNING/TIME button as many times as required to tune in to the desired station. Auto tuning: z When radio interference occurs, auto scan tuning may stop automatically at that point. z To stop the auto tuning, press the TUNING/TIME button again. To receive an FM stereo transmission: Press the TUNER (BAND) button to display the "ST" indicator. FM stereo mode indicator FM stereo receiving indicator z If the FM reception is weak, press the TUNER (BAND) button to extinguish the "ST" indicator. The reception changes to monaural, and the sound becomes clearer. After use: Press the ON/STAND-BY button to enter the power stand-by mode. Sound Control (See page 12. ) ENGLISH E-18 Radio Notes: - Listening to the Radio - When the TUNING/TIME button is pressed for more than 0. 5 seconds, scanning will start automatically and the tuner will stop at the first receivable broadcast station. Listening to the Memorised Station , , Memorising a station You can store 40 AM and FM stations in memory and recall them at the push of a button. (Preset tuning) , , To recall a memorised station Press the PRESET ( the desired station. or ) button for less than 0. 5 seconds to select Frequency and frequency band Preset channel 1 2 - Listening to the Memorised Station - Perform the steps 1 - 3 in "Listening to the Radio" on page 18. Press the MEMORY/SET button to enter the preset tuning saving mode. , , To scan the preset stations The stations saved in memory can be scanned automatically. (Preset memory scan) 3 Within 30 seconds, press the PRESET ( preset channel number. or ) button to select the 1 2 Press the PRESET ( or ) button for more than 0. 5 seconds. Radio The preset number will flash and the programmed stations will be tuned in sequentially, for 5 seconds each. Press the PRESET ( is located. or ) button again when the desired station Store the stations in memory, in order, starting with preset channel 1. 4 Within 30 seconds, press the MEMORY/SET button to store that station in memory. , , To erase entire preset memory 1 2 Press the ON/STAND-BY button to enter the power stand-by mode. Whilst pressing down the TUNER (BAND) button and the X-BASS/DEMO button, press the ON/STAND-BY button until "TUNER CL" appears. If the "MEMORY" and preset number indicators go out before the station is memorised, repeat the operation from step 2. 5 Repeat steps 1 - 4 to set other stations, or to change a preset station. When a new station is stored in memory, the station previously memorised will be erased. Note: The backup function protects the memorised stations for a few hours should there be a power failure or the AC power lead disconnection. E-19 ENGLISH Listening to the Radio (See page 18. ) Listening to a Cassette Tape (TAPE 1) Before playback: z For playback, use normal or low-noise tapes for the best sound. (Metal or CrO tapes are not recommended. ) z Do not use C-120 tapes or poor-quality tapes, as they may cause malfunctions. [. . . ] Purchase a commercially available lead as shown below. , , Listening to the playback sounds from VCR, DVD, etc. to the VIDEO/ AUX sockets. When using video equipment, connect the audio output to this unit and the video output to a television. VCR, DVD, etc. Advanced Features To the line output sockets 2 3 4 Press the ON/STAND-BY button to turn the power on. Play the connected equipment. - Enhancing Your System - White Red Note: To prevent hum interference, place this unit away from a television. Red White , , To record on a tape RCA lead (not supplied) 1 2 3 4 5 Insert a cassette in the TAPE 2 cassette compartment. Press the REC PAUSE ( Press the ( ) or ) button. button. Play the VCR, DVD, etc. , , Headphones z Before plugging in or unplugging the headphones, reduce the volume. [. . . ]