User manual SHARP AR-200

[. . . ] MODEL AR-200 DIGITAL COPYING MACHINE OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · STATUS INDICATORS · GENERAL INFORMATION · OPTIONAL EQUIPMENT · APPENDIX 2 13 27 37 55 71 CAUTIONS Follow the cautions below when using this copier. q q The fusing area is hot. Doing so may damage your eyes. q q q Place the copier on a firm, level surface. When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet. When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet. [. . . ] Layout in 2 in 1 copy* Layout in 4 in 1 copy* Offset of paper output tray Selects a pattern for 2 in 1 copying. The offset function can be specified respectively for the upper and lower areas separated by an optional job separator tray kit. See page 61. * These programs do not affect the copier functions unless certain optional equipment is installed. 37 USER PROGRAMS Setting the user programs 1 Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , and ) blink and "­ ­" appears in the copy quantity display. 2 Enter a program number using the numeric keys. q q The selected program number will blink in the copy quantity display. If a mistake is made in steps 2 to 4, press the CLEAR ( copier will return to step 2. For example, to change the setting of the auto power shut-off timer, press key 3. Program name Auto clear time Preheat mode Auto power shut-off timer Stream feeding mode Auto power shut-off setting Border line for 2 in 1 or 4 in 1 Rotation copy Auto paper select mode Auto tray switching Auditing mode Account number entry Account number change Account number deletion Number of copies per account Resetting account Erase width adjustment Layout in 2 in 1 copy Layout in 4 in 1 copy Offset of paper output tray Program No. The q GENERAL INFORMATION For operation of these programs after step 3, see page 40. User programs 3 Press the START key. q For programs 1 to 9 and 16 to 19, the entered program number will be steadily lit on the left side of the copy quantity display and the currently selected parameter number for the program will blink on the right side. For programs 10 to 15 (programs for auditing accounts), the display varies with the program number. See page 40 for setting programs 10 to 15. q 38 USER PROGRAMS 4 Select the desired parameter using the numeric keys. q The entered parameter number will blink on the right side of the copy quantity display. For example, to change the setting of the auto power shut-off timer to 60 min. , press key 2. q Parameters 0 e OFF 1 e 30 sec. Stream feeding mode * 0 e OFF 1 e ON Auto power shut-off setting 0 e OFF * 1 e ON Border line for 2 in 1 or 4 in 1 * 0 e OFF 1 e ON Rotation copy 0 e OFF * 1 e ON Auto paper select mode 0 e OFF * 1 e ON Auto tray switching 0 e OFF * 1 e ON Erase width adjustment 0 e 0 mm 1 e 5 mm Layout in 2 in 1 copy * 1 e Pattern 1 2 e Pattern 2 Layout in 4 in 1 copy * 1 e Pattern 1 2 e Pattern 2 Offset of paper output tray 0 e Upper OFF, lower OFF 2 e Upper ON, lower OFF Program name Auto clear time * 2 e 60 sec. 5 e 240 min. * 2 e 10 mm 3 e 15 mm 4 e 20 mm 3 e Pattern 3 4 e Pattern 4 * 1e Upper ON, lower ON 3 e Upper OFF, lower ON GENERAL INFORMATION Factory default settings are indicated with an asterisk (*). If you select "0" (OFF) in a program, the corresponding function will be disabled. 5 Press the START key. q The right-hand number in the copy quantity display will be steadily lit and the entered value will be stored. User programs 6 To continue with other user programs, press the key and then repeat steps 2 to 5. To exit the user program mode, press the light ( ) key. q All the alarm indicators will go out. 39 USER PROGRAMS Settings for auditing accounts Setting of user programs No. For settings of all programs, first follow steps 1 to 3 in "Setting the user programs" on page 38 to select a program. Press the START key. ) Then follow the appropriate instructions for the program. Program No. 10: Auditing mode If the auditing mode is enabled, copying is limited to operators with an assigned 3-digit account number. 10 is entered, the current setting (0: OFF, 1:ON) will blink on the right side of the copy quantity display. 1. Select the desired setting using the numeric keys. 0: 1: OFF ON 2. Press the START key. q The setting will be stored. 3. GENERAL INFORMATION User programs To continue with other user programs, press the key and enter another program number. To exit the user program mode, press the light ( ) key. Program No. 11 is entered, "­­­" will blink in the copy quantity display. q If the number of accounts has reached the upper limit (20), "11E" will appear in the copy quantity display. The copier will return to step 2 on page 38. 1. Enter a 3-digit account number using the numeric keys. q Any 3-digit number except "000" can be registered as an account number. 2. Press the START key. q If a number that is already registered or "000" is entered, the number will blink in the copy quantity display. 3. [. . . ] The classification is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. Studies performed in animal models other than rats did not show any association between carbon black and lung tumors. While there have been no studies to date using developer, a two-year cancer bioassay using a typical toner preparation containing carbon black (a small amount of toner is included in the developer mixture) demonstrated no association between toner exposure and tumor development in rats. Signs and Symptoms of Exposure: Minimal irritation to respiratory tract may occur as with exposure to any non-toxic dust. [. . . ]