User manual SHARP AR-161 SECTION 1

[. . . ] MODEL AR-160 AR-161 DIGITAL COPYING MACHINE OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · STATUS INDICATORS · GENERAL INFORMATION · OPTIONAL EQUIPMENT · APPENDIX 2 13 27 36 53 69 CAUTIONS Follow the cautions below when using this copier. q q The fusing area is hot. Doing so may damage your eyes. q q q Place the copier on a firm, level surface. When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet. When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet. [. . . ] To remove it, simply lift the platen cover straight up. q To reattach the platen cover, reverse the above procedure. 15 REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE key or manually with the PRESET RATIO selector (, ) keys and/or the zoom ( , ) keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments. MAKING COPIES Reduction/enlargement/zoom Automatic 1 Place the original on the original table and close the platen cover. 2 3 4 Press the ORIGINAL SIZE ENTER key until the indicator for the size of the original on the original table lights up. Use the TRAY SELECT key to select the paper tray with the desired paper size. q This feature will not work when copy paper of non-standard size is used or the bypass tray is used. Press the AUTO IMAGE key. q q The copy ratio will be automatically set. If the size and orientation of the original do not correspond to standard reduction/enlargement ratios for the selected paper tray, then the ORIGINAL SIZE indicator will blink. However, if an optional electronic sorting kit is installed, the original image may be automatically rotated. If a PRESET RATIO indicator is blinking, part of the original image may not be copied. q 5 6 16 Enter the number of copies. Press the START key. q To cancel the automatic reduction/enlargement mode, press the AUTO IMAGE key again. When copying from an optional SPF with this feature, the automatic reduction/enlargement mode will be automatically cancelled after copying is complete. q REDUCTION/ENLARGEMENT/ZOOM Manual 1 2 A. C. Place the original on the original table and close the platen cover. MAKING COPIES Use the PRESET RATIO selector ( , ) keys and the zoom ( , ) keys to select the desired copy ratio. To select a preset reduction or enlargement copy ratio, press the or key repeatedly until the indicator for the desired copy ratio is lit. Press the or key to set the approximate ratio, then press the key to decrease the ratio or the key to increase the ratio. q q Reduction/enlargement/zoom When a zoom ( , ) key is pressed, the ZOOM indicator will light up and the zoom ratio will be displayed in the copy quantity display for at least two seconds. To verify a zoom setting without changing the zoom ratio, press and hold down the copy ratio display ( ) key. When the key is released, the display will return to the copy quantity display. q D. To decrease or increase the zoom ratio rapidly, press and hold down the or key. However the value will stop at the preset reduction or enlargement ratios. To move beyond these ratios, release the key and then press and hold it down again. Same-size reset: Press the or key repeatedly until the copy ratio returns to 100%. q 3 Ensure that copy paper of the desired size is installed in the paper tray. q If an optional paper feed unit is installed: Use the ORIGINAL SIZE ENTER key to select the original size. Copy paper of the appropriate paper size will be automatically selected depending on the original size and copy ratio. If the selected PRESET RATIO indicator or the ZOOM indicator blinks, the selected copy image is too large for the copy paper size. The desired paper tray can also be selected by pressing the TRAY SELECT key. 4 Set the number of copies and press the START key. 17 BYPASS FEED (special paper) The bypass tray is used to copy onto transparency film, labels, and other special purpose papers. Up to 100 sheets of standard copy paper can be set in the bypass tray. For special purpose papers, the original image must be smaller than the paper or media for copying. If the original image is bigger than the paper or media, this may cause smudges on the edges of the copies. Also for standard copy paper, smudges may appear if the copy paper is not at least as large as the original image. MAKING COPIES Bypass feed (special paper) 1 Unfold the bypass tray. q When feeding B4 or A3 sized paper, extend the feeder tray. 2 Set the paper guides to the copy paper width. 3 Insert the copy paper (print face down) all the way into the bypass tray. q q q q q Up to 100 sheets of standard copy paper measuring from A6 to A3 can be loaded in the bypass tray. [. . . ] Enables or disables the automatic tray switching which occurs when paper in a tray runs out. (This switching cannot switch to the bypass tray. ) Enables or disables the auditing mode, which controls access to copier. The offset function can be specified respectively for the upper and lower areas separated by an optional job separator tray kit. (AR-161 only) 7 8 GENERAL INFORMATION User programs 9 10 11 12 13 14 15 16 17 18 19 * These programs do not affect the copier functions unless certain optional equipment is installed. 36 USER PROGRAMS Setting the user programs 1 Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , and ) blink and "­ ­" appears in the copy quantity display. 2 Enter a program number using the numeric keys. q q The selected program number will blink in the copy quantity display. [. . . ]