User manual SHARP AR-M550N/M550U/M620N/M620U

[. . . ] MODEL MODEL AR-M550U AR-M620U AR-M550N AR-M620N DIGITAL LASER COPIER/PRINTER DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL (for general information and copier operation) Page PART 1: GENERAL INFORMATION BEFORE USING THE PRODUCT MANAGING THE MACHINE PERIPHERAL DEVICES PART 2: COPIER OPERATION 1-1 2-1 3-1 4-1 5-1 6-1 7-1 8-1 MAKING COPIES CONVENIENT COPY FUNCTIONS MACHINE MAINTENANCE (FOR COPYING) DOCUMENT FILING FUNCTION SPECIFICATIONS Be sure to become thoroughly familiar with this manual to gain the maximum benefit from the product. Before installing this product, be sure to read the installation requirements and cautions sections. Be sure to keep all operation manuals handy for reference including this manual, the "Operation manual (for general information and copier operation)" and operation manuals for any optional equipment which has been installed. (Option) Saddle stitch finisher + Punch module + Inserter + Large capacity tray In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". The symbol " " denotes the copier is not completely de-energized but in a stand-by condition at this "POWER" switch position. [. . . ] NOTE The initial setting for the margin width can be changed in the key operator programs to any value from 0 to 20 mm (0 to 1"). (Page 14 of the Key operator's guide) One-sided copying Image shifted Original to the right Image shifted to the left GThe shift direction can be selected from right or left shift as shown in the illustration. Margin Margin Two-sided copying Original Image shifted to the right Image shifted to the left Or Margin Margin 5 the 3 Set [OK]shift amount as needed and touch the key. OK CANCEL OK SIDE 2 20) To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. 1 Touch the [MARGIN SHIFT] key on the special modes screen. The margin shift setting screen will appear. The margin shift icon ( ) will also appear in the upper left of the screen to indicate that the function is turned on. SIDE 1 10 (0 mm 10 (0 mm 1) SPECIAL MODES Use the and the keys to set the shift amount. The shift amount can be set from 0 to 20 mm in 1 mm (0" to 1" in 1/8") increments. MARGIN SHIFT ERASE PAMPHLET COPY JOB BUILD 4 Touch the [OK] key on the special modes screen. You will return to the main screen of copy mode. About the steps that follow If an automatic document feeder is being used, see pages 4-7 through 4-10. To cancel the margin shift function, touch the [CANCEL] key on the margin shift setting screen. 2 Select the shift direction. Touch a shift direction key to select right or left. The selected key will be highlighted. RIGHT LEFT 5-3 SPECIAL MODES Erase The erase function is used to erase the shadow lines on copies produced when copying thick originals or books. The erase width is approximately 10 mm (1/2") in it's initial setting. NOTE The initial setting for the erasure width can be changed in the key operator programs to any value from 0 to 20 mm (0 to 1"). (Page 14 of the Key operator's guide) Original Copy EDGE ERASE Eliminates shadow lines around the edges of copies caused when heavy paper or a book is used as an original. CENTRE ERASE Eliminates shadow lines produced by the bindings of bound documents. EDGE + CENTRE ERASE Eliminates shadow lines around the edges of copies and eliminates the shadow at the centre of copies. To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. 3 Adjust the amount of erase and touch the [OK] key. CANCEL EDGE OK 1 MODES Touch the [ERASE] key on the special modes screen. DUAL C TAN C 10 (0 mm 20) RGIN SHIFT ERASE PHLET COPY JOB BUILD The erase setting screen will appear. The erase icon ( ) will also appear in the upper left of the screen to indicate that the function is turned on. Use the and keys to set the erase width to any value from 0 to 10 mm in 1 mm increments (0" to 1" in increments of 1/8"). 4 Touch the [OK] key on the special modes screen. You will return to the main screen of copy mode. About the steps that follow If an automatic document feeder is being used, see pages 4-7 through 4-10. NOTE When erase is used, edge erase takes place at the edges of the original image. If you also use a ratio setting, the edge erase width will change according to the set ratio. To cancel the erase function, touch the [CANCEL] key on the erase setting screen (step3). 2 Select the desired erase mode. ERASE EDGE ERASE CENTRE ERASE EDGE+CENTRE ERASE Select one of the three erase modes. The selected key will be highlighted. 5-4 SPECIAL MODES Dual page copy The dual page copy function produces separate copies of two documents placed side by side on the document glass. This function is especially useful when copying books and other bound documents. [Example] Copying right and left pages of a book Book original Dual page copy GThe dual page copy function can be used only when copying from the document glass. GOnly A4 (8-1/2" x 11") paper can be used. To display the special modes screen. . . See "General procedure for using special functions" on page 5-2. 4 Ensure that A4 (8-1/2" x 11") size paper is selected. AUTO A4 PAPER SELECT 100% If A4 (8-1/2" x 11") size paper is not selected, touch the [PAPER SELECT] key to select A4 (8-1/2" x 11") size paper. 1 Touch the [DUAL PAGE COPY] key on the special modes screen. OK 1/3 RASE DUAL PAGE COPY TANDEM COPY JOB BUILD The [DUAL PAGE COPY] key will be highlighted to indicate that the function is turned on, and the dual page copy icon ( ) will appear in the upper left of the screen. 2 Touch the [OK] key on the special modes screen. You will return to the main screen of copy mode. About the steps that follow For two-sided copying, follow steps 2 through 4 on page 4-13 and then follow steps 4 through 7 on page 4-12. [. . . ] 4-4 IS Saddle stitch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7, 3-5 Saddle stitch finisher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9, 3-2 Saddle stitch tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6 to 7-12 -Filing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]