User manual SHARP AR-M150/M155

[. . . ] MODEL AR-M150 AR-M155 DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". If your copier is so marked, please read "I" for "ON" and " " for "OFF". The socket-outlet shall be installed near the equipment and shall be easily accessible. If the AR-M150/AR-M155 is used without the facsimile expansion kit AR-FX9, then the following directives are applicable : If the AR-M150/AR-M155 is used with the facsimile expansion kit AR-FX9, please refer to the Declaration Of Conformity in the AR-FX9 operation manual. The CE mark logo label is affixed on an equipment in case that the directives described in the above sentence are applicable to the product. [. . . ] When the settings have been completed, click the "OK" button to close the screen. Button Manager is now linked to the scan menu (1 through 6). The scan settings for each of scan menu 1 through 6 can be changed with the setting window of Button Manager. For the factory default settings of the scan menu and the procedures for configuring Button Manager settings, see "Button Manager Settings" in the Online Manual. 52 SET UP THE SOFTWARE Windows 98/Me/2000 1 2 Click the "Start" button, select "Settings", and then click "Control Panel". Double-click the "Scanners and Cameras" icon. Note If the "Scanners and Cameras" icon does not appear in Windows Me, click "view all Control Panel options". 3 4 5 Select "SHARP AR-M155" and click the "Properties" button. In Windows Me, right click "SHARP AR-M155" and click "Properties" in the pop-up menu. In the "Properties" screen, click the "Events" tab. Select "SC1:" from the "Scanner events" pull-down menu. 5 53 SET UP THE SOFTWARE 6 Select "Sharp Button Manager E" in "Send to this application". Note If other applications are shown, deselect the checkboxes for the other applications and leave only the Button Manager checkbox selected. 7 8 Click the "Apply" button. Repeat Steps 5 through 7 to link Button Manager to "SC2:" through "SC6:". Select "SC2:" from the "Scanner events" pull-down menu. Select "Sharp Button Manager E" in "Send to this application" and click the "Apply" button. When the settings have been completed, click the "OK" button to close the screen. Button Manager is now linked to the scan menu (1 through 6). The scan settings for each of scan menus 1 through 6 can be changed with the setting window of Button Manager. For the factory default settings of the scan menu and the procedures for configuring Button Manager settings, see "Button Manager Settings" in the Online Manual. 54 CONNECTING THE MACHINE TO YOUR COMPUTER Connecting a USB cable Follow the procedure below to connect the machine to your computer. A USB cable for connecting the machine to your computer is not included with the machine. Please purchase the appropriate cable for your computer. Caution · USB is available with a PC/AT compatible computer that was originally equipped with USB and had Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or Windows XP Home Edition preinstalled. · Do not connect the USB cable before installing the MFP driver. The USB cable should be connected during installation of the MFP driver. · If the machine will be connected using a USB 2. 0 port of your computer, please purchase a USB cable that supports USB 2. 0. · The machine's USB connector will transfer data at the speed specified by the USB 2. 0 (Hi-Speed) only if the Microsoft USB 2. 0 driver is preinstalled in the computer, or if the USB 2. 0 driver for Windows 2000 Professional/XP that Microsoft provides through its "Windows Update" Web page is installed. · To obtain the fastest USB 2. 0 data transfer speed, "USB2. 0 MODE SWITCH" in the machine's user programs must be set to "HI-SPEED". · Use the machine's "HI-SPEED" mode only when using a computer that is running Windows 2000/XP. · Even when the Microsoft USB 2. 0 driver is used, it may not be possible to obtain full USB 2. 0 speed if a PC card supporting USB 2. 0 is used. To obtain the latest driver (which may enable a higher speed), contact the manufacturer of your PC card. · Connection is also possible using a USB 1. 1 port on your computer. However, the specifications will be USB 1. 1 specifications (Full-Speed). Note 5 1 Insert the cable into the USB connector on the machine. 2 Insert the other end of the cable into your computer's USB port. 55 SET UP THE SOFTWARE Connecting a parallel cable 1 2 Obtain an IEEE1284 shielded parallel interface cable. [. . . ] : Use of a dust mask and goggles are recommended when handling a large quantity of toner or during long term exposure, as with any non-toxic dust. 3 3 MATERIAL SAFETY DATA SHEET Page: 3/4 Date Revised :Jul. 31, 2002 Date Issued :Nov. 1. F-31001 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance Physical State : Solid Ph Boiling / Melting Point Flash Point(°C) lgnition Point(°C ) Explosion Properties Density(g/cm³) Solubility in Water Form : Powder Color : Black : Not applicable : Not applicable : Not applicable : No data : No data : 7. 3 (bulk density : 2. 0) : Negligible Odor : odorless 10. STABILITY AND REACTIVITY Stability Hazardous Reactions Conditions to Avoid Materials to Avoid Hazardous Decomposition Products Further Information : Stable : Dust explosion, like most finely divided organic powders. : Oxidizing Materials : CO, CO2 and NOX : None 11. TOXICOLOGICAL INFORMATION Acute Toxicity Ingestion(oral) Inhalation Dermal Eye irritation Skin irritation Skin sensitizer Mutagenicity Carcinogenicity : LD50 > 2000mg/kg (Rats) : No data : No data : Not an irritant (Rabbits) : Not an irritant (Rabbits) : No sensitization : Negative (Ames Test) : In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human carcinogen). This classification is given to chemicals for which there is inadequate human evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. [. . . ]