User manual SHARP AR-5015N/5020

[. . . ] MODEL AR-5015 N AR-5020 DIGITAL LASER COPIER OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · STATUS INDICATORS · GENERAL INFORMATION · OPTIONAL EQUIPMENT 2 13 28 35 53 CAUTIONS Follow the cautions below when using this copier. G G The fusing area is hot. Doing so may damage your eyes. G G G Place the copier on a firm, level surface. When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet. When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet. [. . . ] Be sure to only shake the cartridge before the tape is removed. Shutter 28 TONER CARTRIDGE REPLACEMENT 5 Gently insert the toner cartridge along the guides until it locks in place while pushing the lock release lever. If dirt or dust is adhered to the toner cartridge, remove it before installing the cartridge. 6 7 Remove the tape from the shutter. Pull the shutter out of the toner cartridge as shown in the illustration. Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover. The indicator will go out. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. Even after a new toner cartridge is installed, the START key ( ) indicator may not light up, indicating copying cannot be restarted (toner is not sufficiently fed). The copier will feed toner again approximately 2 minutes and then copying can be restarted. STATUS INDICATORS Toner cartridge replacement Toner cartridge life To find out the approximate quantity of toner remaining, follow the procedure below. 1 2 3 Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , and ) blink and "­­" appears in the copy quantity display. Press and hold the copy ratio display ( than 5 seconds. G ) key for more The approximate quantity of toner remaining will be indicated in the copy quantity display as a percentage. ( "100", "75", "50", "25", or "10" is displayed. ) When the percentage is less than 10%, "LO" will be displayed. Press the light ( G ) key. All the alarm indicators will go out. 29 MISFEED REMOVAL The copier will stop when a misfeed occurs. The misfeed ( ) indicator will blink, and blinking red misfeed location indicators will indicate the approximate misfeed location. If paper is accidentally torn during removal, be sure to remove all pieces. For misfeeds in optional equipment, see its section of the operation manual. First confirm the misfeed location. ( ( P. 30, 33) STATUS INDICATORS Misfeed in the bypass tray 1 2 Gently pull the misfed paper out. Misfeed removal Lift slightly on the side cover and slide the cover out until it stops. Close the side cover by pressing the handle on the cover. G The misfeed ( ) indicator will go out. Misfeed in the copier 1 30 Open the bypass tray. Lift slightly on the side cover and slide the cover out until it stops. MISFEED REMOVAL 2 If the misfed paper is seen from this side, proceed to C. Remove the misfed paper following the instructions for each location in the illustration below. If paper is misfed here, proceed to B. Misfeed in the fusing area . If paper is misfed here, proceed to A. Misfeed in the paper feed area . A. Misfeed in the paper feed area Push gently on both sides of the front cover and open it. 1 2 STATUS INDICATORS Roller rotating knob Carefully remove the misfed paper. Turn the roller rotating knob in the direction of the arrow to assist in removing it. The fusing unit is hot. Take care in removing paper. Misfeed removal Do not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may damage the drum and cause smudges on copies. 3 Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover. G The misfeed ( ) indicator will go out. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged. B. Misfeed in the fusing area Push gently on both sides of the front cover and open it. 1 31 MISFEED REMOVAL Roller rotating knob 2 3 Turn the roller rotating knob in the direction of the arrow. Carefully remove the misfed paper. [. . . ] There may be some deviations from these values in individual units. 52 OPTIONAL EQUIPMENT CONTENTS G Page SINGLE PASS FEEDER (AR-SP2) . 56 OPTIONAL EQUIPMENT 53 SINGLE PASS FEEDER (AR-SP2) The single pass feeder (SPF) holds up to 30 originals for automatic feeding. PART NAMES Original guides Document feeder tray Feeding roller cover Exit area Right side cover Single pass feeder (AR-SP2) OPTIONAL EQUIPMENT Specifications Acceptable originals Weight: 56 to 90 g/m2 (15 to 24 lbs. ) Size: A5 to A3 (5-1/2" x 8-1/2" to 11" x 17") Capacity: Up to 30 sheets provided the total aggregate thickness does not exceed 4 mm (5/32") A5, A4, A4R, B4, A3 (5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13", 8-1/2" x 14", 11" x 17") Drawn from the copier Approx. 5. 3 kg (11. 7 lbs. ) 583 mm (W) x 435 mm (D) x 131 mm (H) (22-61/64" (W) x 17-1/8" (D) x 5-5/32" (H)) Detectable original sizes Power supply Weight Dimensions As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. [. . . ]