User manual SHARP AR-206

[. . . ] MODEL AR-206 DIGITAL LASER COPIER OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · STATUS INDICATORS · GENERAL INFORMATION · OPTIONAL EQUIPMENT 2 13 28 36 55 CAUTIONS Follow the cautions below when using this copier. G G The fusing area is hot. Doing so may damage your eyes. G G G Place the copier on a firm, level surface. When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet. When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet. [. . . ] To exit the user program mode, press the light ( ) key. G All the alarm indicators will go out. 38 USER PROGRAMS Settings for auditing accounts Setting of user programs No. For settings of all programs, first follow steps 1 to 3 in "Setting the user programs" on page 37 to select a program. Press the START key. ) Then follow the appropriate instructions for the program. Program No. 10: Auditing mode If the auditing mode is enabled, copying is limited to operators with an assigned 3-digit account number. 10 is entered, the current setting (0: OFF, 1:ON) will blink on the right side of the copy quantity display. 1. Select the desired setting using the numeric keys. 0: 1: OFF ON 2. Press the START key. G The setting will be stored. 3. To continue with other user programs, press the key and enter another program number. To exit the user program mode, press the light ( ) key. GENERAL INFORMATION Program No. 11 is entered, "­­­" will blink in the copy quantity display. G If the number of accounts has reached the upper limit (20), "11E" will appear in the copy quantity display. The copier will return to step 2 on page 37. User programs 1. Enter a 3-digit account number using the numeric keys. G Any 3-digit number except "000" can be registered as an account number. 2. Press the START key. G If a number that is already registered or "000" is entered, the number will blink in the copy quantity display. 3. To continue with other user programs, press the key and enter another program number. To exit the user program mode, press the light ( ) key. 39 USER PROGRAMS Program No. 12 is entered, an account number will appear in the copy quantity display. G If no account number has been registered, "12E" will appear in the copy quantity display. The copier will return to step 2 on page 37. 1. Use the copy ratio display ( number to be changed. G ) key to select the account Use the key to advance through the account numbers. 2. Press the START key. G The account number will be erased and "­­­ " will blink in the copy quantity display. 3. Press the START key. G If a number that is already registered or "000" is entered, the number will blink in the copy quantity display. 5. To continue with other user programs, press the key and enter another program number. To exit the user program mode, press the light ( ) key. Program No. 13 is entered, "0" will blink on the right side of the copy quantity display. G If no account number has been registered, "13E" will appear in the copy quantity display. The copier will return to step 2 on page 37. GENERAL INFORMATION 1. Press the START key. G User programs If you have pressed the 0 key in step 1, an account number will appear in the copy quantity display. Proceed to step 5. G 3. Use the copy ratio display ( number to be deleted. G ) key to select the account Use the key to advance through the account numbers. 4. [. . . ] The classification is based upon the development of lung tumors in rats receiving chronic inhalation exposures to free carbon black at levels that induce particle overload of the lung. Studies performed in animal models other than rats did not show any association between carbon black and lung tumors. While there have been no studies to date using developer, a two-year cancer bioassay using a typical toner preparation containing carbon black (a small amount of toner is included in the developer mixture) demonstrated no association between toner exposure and tumor development in rats. Signs and Symptoms of Exposure: Minimal irritation to respiratory tract may occur as with exposure to any non-toxic dust. [. . . ]