User manual SHARP AR-163

[. . . ] MODEL AR-163 DIGITAL LASER COPIER OPERATION MANUAL Page · GETTING STARTED · MAKING COPIES · STATUS INDICATORS · GENERAL INFORMATION · OPTIONAL EQUIPMENT 2 13 28 35 53 CAUTIONS Follow the cautions below when using this copier. G G The fusing area is hot. Doing so may damage your eyes. G G G Place the copier on a firm, level surface. When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet. When moving the copier, be sure to turn the power switch off and remove the power cord from the outlet. [. . . ] The G GENERAL INFORMATION For operation of these programs after step 3, see page 38. User programs 3 Press the START ( G ) key. For programs 1 to 9 and 16 to 19, the entered program number will be steadily lit on the left side of the copy quantity display and the currently selected parameter number for the program will blink on the right side. For programs 10 to 15 (programs for auditing accounts), the display varies with the program number. See page 38 for setting programs 10 to 15. G 36 USER PROGRAMS 4 Select the desired parameter using the numeric keys. G The entered parameter number will blink on the right side of the copy quantity display. For example, to change the setting of the auto power shut-off timer to 60 min. , press key 2. G Program name Auto clear time Parameters 0 OFF 1 30 sec. Stream feeding mode *0 OFF 1 ON Auto power shut-off setting 0 OFF *1 ON Border line for 2 in 1 or 4 in 1 * 0 OFF 1 ON Rotation copy 0 OFF *1 ON Auto paper select mode 0 OFF *1 ON Auto tray switching 0 OFF *1 ON Erase width adjustment 0 0 mm 1 5 mm (0 0" 1 1/4" Layout in 2 in 1 copy *1 Pattern 1 2 Pattern 2 Layout in 4 in 1 copy *1 Pattern 1 2 Pattern 2 Offset of paper output tray 0 Upper OFF, lower OFF 2 Upper ON, lower OFF G *2 2 3 60 sec. 240 min. *2 *2 3 *1 3 10 mm 1/2" 3 3 15 mm 3/4" 4 4 20 mm 1") Pattern 3 4 Pattern 4 Upper ON, lower ON Upper OFF, lower ON GENERAL INFORMATION Factory default settings are indicated with an asterisk (*). ** In European countries, the default setting of the preheat mode is 1 ( 30 sec. ). For other programs, factory default settings in these countries are same to those shown above with an asterisk (*). If you select "0" (OFF) in a program, the corresponding function will be disabled. 5 Press the START ( G ) key. The right-hand number in the copy quantity display will be steadily lit and the entered value will be stored. User programs 6 To continue with other user programs, press the key and then repeat steps 2 to 5. To exit the user program mode, press the light ( ) key. G All the alarm indicators will go out. 37 USER PROGRAMS Settings for auditing accounts Settings of user programs No. For setting of all programs, first follow steps 1 to 3 in "Setting the user programs" on page 36 to select a program. Press the START ( ) key. ) Then follow the appropriate instructions for the program. Program No. 10: Auditing mode If the auditing mode is enabled, copying is limited to operators with an assigned 3-digit account number. 10 is entered, the current setting (0: OFF, 1:ON) will blink on the right side of the copy quantity display. 1. Select the desired setting using the numeric keys. 0: 1: OFF ON 2. Press the START ( G ) key. The setting will be stored. 3. To continue with other user programs, press the key and enter another program number. To exit the user program mode, press the light ( ) key. GENERAL INFORMATION Program No. 11 is entered, "­ ­ ­" will blink in the copy quantity display. G If the number of accounts has reached the upper limit (20), "11E" will appear in the copy quantity display. The copier will return to step 2 on page 36. User programs 1. Enter a 3-digit account number using the numeric keys. G Any 3-digit number except "000" can be registered as an account number. 2. Press the START ( G ) key. If a number that is already registered or "000" is entered, the number will blink in the copy quantity display. 3. To continue with other user programs, press the key and enter another program number. To exit the user program mode, press the light ( ) key. 38 USER PROGRAMS Program No. 12 is entered, an account number will appear in the copy quantity display. G If no account number has been registered, "12E" will appear in the copy quantity display. [. . . ] Telephone number for information: 01923-474013 Canada United Kingdom Section 3. Ingredients CAS No. 7439-89-6 29497-14-1 1333-86-4 Proportion > 92. 5% < 7. 0% < 0. 5% OSHA PEL Not listed Not listed 3. 5mg/m3 ACGIH TLV Not listed Not listed 3. 5mg/m3 Other Limits None None None Ingredients Iron powder Styrene-Acrylate copolymer Carbon black Section 4. Hazardous Identification (Emergency Overview) Developer is a black powder containing small amounts of toner, and possessing no immediate hazard. There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. Section 5. Health Hazard Data Inhalation?Health Hazards: Acute oral toxicity ------------ LDL0 of this toner which is included in this developer is over 2, 000mg/kg. [. . . ]