User manual SHARP AR-121E/151E

[. . . ] MODEL AR-121E AR-151E DIGITAL LASER COPIER OPERATION MANUAL Page · GETTING STARTED · INSTALLATION · MAKING COPIES · SPECIAL FUNCTIONS · SUPPLIES AND USER MAINTENANCE · COPIER TROUBLE?· APPENDIX 3 8 11 17 20 25 32 cover-1_AR121151EX. p65 2 30/11/00, 19:07 CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT VAROITUS!LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. VARNING OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1. Laserstrahl R CAUTION INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. [. . . ] The exposure indicator marked "1" will light up, indicating the standard toner mode is active. 3 To enter the high image quality mode, press the dark ( ) key. The exposure indicator marked "5" will light up, indicating the high image quality mode is selected. 4 Special functions 4 Press the exposure mode selector key twice. The photo ( ) indicator will stop blinking and the AUTO indicator will light up steadily. To return to the standard mode, repeat the procedure but use the light ( to select exposure level "1" in step 3. ) key USER PROGRAMS (power save modes, auto clear time) The user programs allow the parameters of certain functions to be set, changed, or cancelled as desired. Setting the power save modes and auto clear time 1 Press and hold down the light ( ) and dark ( ) keys simultaneously for more than 5 seconds until all the alarm indicators ( , , and ) blink and "­ ­" appears in the display. Use the left copy quantity ( ) key to select a user program number (1: auto clear time, 2: preheat mode, 3: auto power shut-off timer, 5: auto power shut-off mode). The selected number will blink in the left side of the display. 2 18 chap-4_AR121151EX. p65 18 30/11/00, 19:08 USER PROGRAMS 3 4 Press the print ( ) key. The entered program number will be steadily lit and the currently selected parameter number for the program will blink on the right side of the display. Select the desired parameter using the right copy quantity ( parameter number will blink on the right of the display. 1 2 3 5 Mode Auto clear time Preheat mode Auto power shutoff timer Auto power shutoff mode 0 3 0 0 3 0 OFF 90 sec. 4 OFF *1 Factory default settings are indicated with an asterisk (*). 4 Special functions 5 Press the print ( ) key. The right-hand number in the display will be steadily lit and the entered value will be stored. To change the setting or to set another mode, press the clear ( copier will return to step 2. ) key. The 6 Press the light ( ) or dark ( ) key to return to the normal copy mode. DISPLAYING TOTAL NUMBER OF COPIES Use the following procedure to display the total number of copies. 1 2 Press the clear ( ) key to reset the display to zero. Press and hold down the clear ( ) key for approximately 5 seconds. The total number of copies will appear in two steps, each with three digits. Example: Total number of copies is 1, 234. 19 chap-4_AR121151EX. p65 19 30/11/00, 19:08 5 SUPPLIES AND USER MAINTENANCE Be sure to use only genuine SHARP parts and supplies. This chapter describes how to replace the toner cartridge. TONER CARTRIDGE REPLACEMENT When the toner cartridge replacement required ( ) indicator lights up, replacement of the toner cartridge will be needed soon. When the toner cartridge replacement required ( ) indicator blinks, the toner cartridge must be replaced before copying can be resumed. During a long copy run of a dark original, the ready ( ) indicator may blink, the indicator light up, and the copier stop, even though toner is left. The copier will feed toner up to 2 minutes and then the ready ( ) indicator will light up. Then, push gently on both sides of the front cover and open it. 5 Supplies and user maintenance 1 2 Push the toner cartridge lock release lever and pull the toner cartridge out. Dispose of the old toner cartridge in accordance with local regulations. Toner cartridge lock release lever After removing the toner cartridge, do not shake it or tap on it. Put the old cartridge immediately in the bag contained in the box of the new cartridge. 20 chap-5_AR121151EX. p65 20 30/11/00, 19:08 TONER CARTRIDGE REPLACEMENT 3 Remove the toner cartridge from the bag. Grasp the cartridge on both sides and shake it horizontally four or five times. [. . . ] One or two exposure indicators corresponding to the automatic exposure level which has been selected will light up. 3 Press the light ( ) or dark ( ) key to lighten or darken the automatic exposure level as desired. If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously. 6 Copier trouble? 4 Press the exposure selector key. This automatic exposure level will remain in effect until you change it again by this procedure. 31 chap-6_AR121151EX. p65 31 30/11/00, 19:08 7 Type Copy system Originals Original size Copy sizes Copy speed APPENDIX Digital copying machine, desk-top type Dry, electrostatic transfer Sheets, bound documents Max. [. . . ]