User manual SHARP 21QF2-U

[. . . ] Example of side terminals usage E6 TV To Audio/Video out terminals DVD Player VCR Remote Control Size-AA batteries Operation manual Camcorder E3 ANTENNA CONNECTION Connecting to an antenna via a VCR TV Video Game Connecting to an antenna Yellow : To VIDEO White : To AUDIO VCR 300-ohm twin-lead flat feeder (not supplied) 75-ohm impedance converter (not supplied) Example of rear terminals usage TV For Playback 75-ohm coaxial cable (round cable) (not supplied) Standard DIN45325 plug (IEC 169-2) Antenna in To antenna in terminal To RF out terminal Yellow : To VIDEO White : To AUDIO DVD Player For Recording and Editing VCR To Audio/Video out terminals If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325 plug (IEC 169-2), plug it into the antenna jack at the rear of the set. If your outdoor antenna uses a 300-ohm twin-lead flat feeder, connect a 300-ohm to 75-ohm impedance converter and plug it into the antenna jack at the rear of the set. To Audio/Video out terminals VCR To Audio/Video in terminals · When using the RF terminal connection, set the TV to channel zero to make initial adjustments for the VCR. · The audiovisual cords required to connect the TV set with video equipment may differ from those shown in the above diagram. See the operation manual of your video equipment for connection details. · The above recording and editing connections are intended solely for personal use and not for the illegal copying of audiovisual material protected by copyright laws. 21QF2-U_EN. indd 2 12/28/07 12:12:06 PM E5 TV set PART NAMES E5 PART NAMES (Continued) Infrared transmitter window Aim this window at the infrared sensor window on your TV set. Remote control TV/VIDEO Turns the TV on or to Standby mode. 1 2 5 8 0 TV/VIDEO Switches between TV broadcasts and A/V input programmes. [. . . ] To turn off SKIP, press the number buttons to select the desired channel and then set "SKIP" to "OFF". · MANUAL (FINE tuning) / is pressed, the frequency i) Each time changes to allow fine tuning and the colour of channel number changes to yellow to indicate fine tuning. ii) Press / for more than 2 seconds, the "Manual Channel Tuning" will start. Press Auto tuning bar will shown during Auto Search only. POSITION COLOUR SOUND SKIP MANUAL AUTO SELECT: CH ADJUST: 27 AUTO B/G OFF 168. 25MHz RETURN:MENU / CH · Press CH and channels change as shown below. / 2 / 1 / 0 . . . @ With the number buttons (on remote control) 5 · To select a one-digit channel, such as 5, press If "5-" is indicated, press to select one-digit 5 input, and then press again. · To select a two-digit channel, such as 15, press 1 to select the two-digit input. Press , and then 5 press . . ­­ 1­ 15 PAL B/G POSITION COLOUR SOUND SKIP MANUAL AUTO SELECT: CH ADJUST: 27 AUTO B/G OFF 168. 25MHz RETURN:MENU ^ Press MENU until normal screen appears. POSITION COLOUR AV1 AUTO Adjusting volume !Adjust volume using / . VOLUME 10 · When you select AV1, AV2 for the channel position, the CH-SETTING menu changes as shown on the right and the colour mode changes in the following order: AUTO PAL SECAM NTSC4. 43 NTSC3. 58 · The volume bar disappears approximately three seconds after the volume has been adjusted. SELECT: CH ADJUST: RETURN:MENU · When the power indicator lights up dimly, either CH / CH on the TV can be pressed to turn on the power. · Channels that have been skipped cannot be selected by CH / CH . Use TV/VIDEO to select this · The AV1, AV2 input channel cannot be selected using CH channel. · Switching COLOUR system: Set the system to "AUTO" for normal TV reception. The AUTO mode automatically detects the receiving signal system and changes the reception system of the TV set. When the picture is not stable, switching to an appropriate system may improve the picture quality. · Switching SOUND system: When the sound is not stable, switching to an appropriate system may improve the sound quality. 21QF2-U_EN. indd 4 12/28/07 12:12:07 PM E7 !Press @ Press # Press $ Press items. SETTING AND ADJUSTMENT (Continued) TV/VIDEO E8 2 5 8 0 3 6 9 FEATURES TV/VIDEO Picture adjustment MENU Off timer Automatically turns power off after a set length of time has passed. CH CH 1 4 2 5 8 0 to call MENU screen. / to select PICTURE icon. CH CONTRAST COLOUR BRIGHTNESS TINT SHARPNESS WHITE TEMP SELECT: ENTER: CH 50 0 +10 ­10 RETURN:MENU 1 4 7 3 6 9 !Press @ Press CH CH TIMER to call "OFF / ". OFF TV PASSWORD BLUE BACK ­­:­­ OFF 0000 OFF 7 CH CH MENU CH / / to enter PICTURE menu. [. . . ] Example: After switching from channel 5 to channel 7, the channel will change to channel 5. is pressed, again to PAL TIMER NORMAL PAL Sound OK, picture poor. Picture rolls vertically. PAL TV Picture OK, sound poor. Picture lines or streaks. 7 Problems 5 LANGUAGE Remote control does not work. TV / Video selection Switches between TV broadcasts and AV input programmes. · Each time you press the TV/VIDEO , the input switches between AV1, AV2 and TV programme. Possible Causes/Remedies AV1 AV2 25 PAL B/G Try a new channel to check for possible station trouble. [. . . ]