User manual SFA SANIVITE

[. . . ] € If the non-return valve is installed horizontally, the arrow should show along the top. TECHNICAL ADVICE FOR DISCHARGE If the unit is discharging to a point much lower than the unit (say a floor lower) to avoid siphoning, install a vacuum breaker (capable of withstanding 10 psi pressure) at the high point of the installation. SANISHOWER/SANIPUMP 1 is a pump which will clear the waste from a shower and washbasin. Note: Sanishower will only accept the waste from a shower discharging at maximum 15 liters per minute. [. . . ] The unit should be connected to a fully earthed electrical supply (class 1). It must be wired into an unswitched fused fixed wiring connector protected by a 5 amp fuse and a residual current detector (30 mA). 7c CONNECTION OF BATHROOM APPLIANCES (SANISHOWER® and SANIPUMP 1®) To install a shower next to the unit, connect one end of the connector to the inlet spigot, and the other end to the 40mm shower waste. Warning : Ensure that the shower trap exit is 60mm above ground level. Installation under the tray : Lift the tray at least 145mm to accomodate the unit. Warning : Prepare an access trap to the unit of at least L-400mm and H- 145mm (the access trap should be built so that tool is required to open it). The Sanishower/Sanipump 1 should always be accessible for possible maintenance. Stanley knife) to remove the cap from the optional inlet (see picture 7c bis). Make sure the hole is not cut at an angle, and that the edges are deburred. Warning : Make sure that this operation is carried out precisely, otherwise the joint will not be watertight. If fitting 32 mm waste, cut off the end of connector C (see picture 7c bis). Warning: Ensure the electricity is turned OFF at the main switch board before wiring to connector. All work on cable and motor should only be carried out by a qualified Saniflo servicing agent, as special tools are required. SANISHOWER® and SANIPUMP 1® : Connect the wires in accordance with their colour coding : live = brown neutral = blue earth = yellow/green 8 STANDARD • The unit conforms with EN 12050-2 effluent lifting station and the European directives and standards concerning electrical safety and electromagnetic compatibility. 9 CARE AND USE SANIVITE®, SANISPEED® and SANIPUMP 2® are designed to handle the waste evacuation from a bath domestic kitchen sink, dishwasher and washing machine - all working at the same time if required. SANISHOWER®/SANIPUMP 1® is designed to take the waste from a shower and handbasin. Warning : Do not dispose of solvents, paints (do not wash paint brushes in sink), caustic, acid or other chemicals into these products. Depending on usage, the SANIVITE®, SANISPEED® and SANIPUMP 2® may need to be cleaned from time to time. The SANIVITE® unit will pump away water as hot as 60°C for 5 minutes, SANISPEED® and SANIPUMP 2® pump 75°C for 5 minutes (i. However, do not pour boiling water directly into the SANIVITE®, SANISPEED® and SANIPUMP 2® unit. [. . . ] In case of a service requirement, please call own Saniflo service engineer, especially for any electrical work. Dette apparat er ikke beregnet til at blive brugt af personer (herunder børn) hvis fysiske, sensoriske eller mentale evner er svækkede eller personer blottet for erfaring eller kendskab, med mindre de er under opsyn eller har modtaget instruktioner om brugen af apparatet af en person, der er ansvarlig for deres sikkerhed. INSTALLASJON UNDER DUSJKARET Denne type installasjon får kun utføres av fagmann og pumpen må ikke utsettes for vann/vannsprut. Experience and knowledge, unless they are monitored and are given the necessary instructions for using the device, with the help of a person responsible for their safety. [. . . ]