User manual SEW-EURODRIVE 222

[. . . ] The software described in this guide is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of the agreement. Compaq, Fastart, ROMPaq, QVision, SmartStart, NetFlex, QuickFind, PaqFax, registered United States Patent and Trademark Office. Netelligent, SoftPaq, QuickLock, PowerStorm are trademarks and/or service marks of Compaq Computer Corporation. [. . . ] The Remote Management Administrators Guide is included with the Remote Management Administration Tools, and is available in the Support Software CD Kit or at the Compaq website www. compaq. com. Writer: Jeff Parmenter Project: Compaq Professional Workstation 222 Reference Guide Comments: 338521-002 File Name: D-CH03. DOC Last Saved On: 2/11/99 8:20 PM SEW-EURODRIVE CONFIDENTIAL - NEED TO KNOW REQUIRED 3-27 Power Management The power management feature shuts down certain components of the workstation when they are not in use, saving energy without having to shut down the workstation. To enable, customize, or disable standby time-outs, follow these steps: 1. When you see the words "F10=Setup" in the bottom-right corner of the screen, press the F10 key. NOTE: If you do not press the F10 key while the message is displayed, you must turn the workstation off, then on again, to access the utility. Press the Enter key to bypass the welcome screens and display the Compaq Utilities menu. From the Compaq Utilities menu, select Computer Setup, then press the Enter key. NOTE: When using a power-managed system, disable monitor time-outs in Computer Setup first, then establish the settings in the operating system, to avoid potential conflicts. Use Display Properties to establish, modify, or disable Power Management settings for the monitor. To access Display Properties, right-click on the Windows Desktop, then select Properties. Compaq Professional Workstation 222 Reference Guide Writer: Jeff Parmenter Project: Compaq Professional Workstation 222 Reference Guide Comments: 338521-002 File Name: D-CH03. DOC Last Saved On: 2/11/99 8:20 PM SEW-EURODRIVE CONFIDENTIAL - NEED TO KNOW REQUIRED 3-28 Intelligent Manageability Advanced Configuration and Power Interfaces (ACPI)-Ready Hardware ACPI defines a hardware interface that allows a standard way to integrate power management features throughout the workstation system, including hardware, operating system, and application software. This enables the workstation to automatically turn on and off peripherals such as CD-ROMs, network cards, hard drives, and printers. With the ACPI technology, peripherals will also be able to activate the workstation. Your workstation comes Ethernet network ready, which means that it has a preinstalled network controller and preinstalled network drivers. The Compaq NC3161 Fast Ethernet Embedded 10/100 with Wake-on-LAN supports a PCI bus mastering, dual speed 10BaseT, and 100BaseTX controller that will automatically detect network connection speed and adjust accordingly. The controller supports full duplex Ethernet, allowing two-way transmission between nodes for up to 20 or 200 Mbytes/sec aggregate bandwidth. To connect to a Token Ring Network, you must install a Token Ring board. Compaq Professional Workstation 222 Reference Guide Writer: Jeff Parmenter Project: Compaq Professional Workstation 222 Reference Guide Comments: 338521-002 File Name: E-CH04. DOC Last Saved On: 2/11/99 8:44 PM SEW-EURODRIVE CONFIDENTIAL - NEED TO KNOW REQUIRED 4-2 Network Communications Connecting to an Ethernet Network An RJ-45 Ethernet network connector is included on your workstation. Refer to the following illustration to connect a network cable to the RJ-45 connector. IMPORTANT: If you are connecting to a 100BaseTX network, you must use a Category 5 UTP cable. Figure 4-1. Attaching the network cable to the RJ-45 connector Any RJ-45 receptacle marked with these symbols indicates a Network Interface Connection. WARNING: To reduce risk of electrical shock, fire, or damage to the equipment, do not plug telephone or telecommunications connectors into this receptacle. Installing the Network Driver The network device driver enables the workstation to communicate with the network. For information about installing the driver, operating system, and other support software, refer to the Software Installation Guide. Writer: Jeff Parmenter Project: Compaq Professional Workstation 222 Reference Guide Comments: 338521-002 File Name: E-CH04. DOC Last Saved On: 2/11/99 8:44 PM SEW-EURODRIVE CONFIDENTIAL - NEED TO KNOW REQUIRED 5-1 Chapter 5 CD-ROM Drive and PremierSound Audio System Your workstation includes a CD-ROM drive (IDE) and a PremierSound Audio System. The CD-ROM drive is a random access, read-only storage device capable of retrieving data from a removable compact disc. The PremierSound Audio System provides sound capabilities for increased productivity in the Windows NT Workstation operating environment. Using the Tray-Load CD-ROM Drive To insert a CD, refer to the illustration below. Figure 5-1. [. . . ] Graphics display controller Diskette controller circuitry Mismatch in drivetype Action Replace the monochrome display controller. Run Computer Setup or Windows NT Workstation utilities. 501-Display Adapter Failure 601-Diskette Controller Error 605-Diskette Drive Type Error 611-Primary Floppy Port Address Assignment Conflict 612-Secondary Floppy Port Address Assignment Conflict 1151-System Board COM Port 1 Address Assignment Conflict 1152- System Board COM Port 2 Address Assignment Conflict Replace the graphics controller. Contact your Compaq authorized service provider. Run Computer Setup or Windows NT Workstation utilities. Configuration error Configuration error Run Computer Setup or Windows NT Workstation utilities. Configuration Error Run Computer Setup Configuration Error Run Computer Setup Continued Writer: kmosby Project: Compaq Professional Workstation 222 Reference Guide Comments: 338521-002 File Name: P-APPD. DOC Last Saved On: 12/15/98 6:30 PM SEW-EURODRIVE CONFIDENTIAL - NEED TO KNOW REQUIRED D-5 POST Error Messages and Codes Continued Error Code 1155-COM Port Address Assignment Conflict 1610-Temperature violation detected Probable Source of Problem Both external and internal serial ports. Action Run Computer Setup or Windows NT Workstation utilities. The system is too hot. Turn off the workstation and let it cool off. If the condition persists, Run Diagnostics to get more information; then contact your Compaq authorized service provider. [. . . ]