User manual SENTROL ZXLED8
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SENTROL ZXLED8. We hope that this SENTROL ZXLED8 user guide will be useful to you.
Manual abstract: user guide SENTROL ZXLED8
Detailed instructions for use are in the User's Guide.
[. . . ] How to Use Your Moose Security System
ZXLED8/ZXLED1 2
Control Station
READY TROUBLE FIRE
1 5 9
2 6 10
3 7 11
4 8 12
VIEW INFO
ALM MEM
EVENT LOG
OFF CANCEL
D
1
BYPASS
2
DELAY ARM
3
CHIME
4
AWAY
RST SMOKE
5
TEST
6
PROGRAM
7
QUIT
8
ACCESS
9
INSTANT
STAY CLEAR
HOME
0
B
ENTER
NEXT
NIGHT
A
C
PREV
1 (ZXLED12 shown)
INTRODUCTION Thank you for choosing the ZX200/ZX210 or ZX400/ZX410 Security Control. This
control will provide you with years of reliable operation when properly installed and maintained. To maximize the benefits of your Security System, it is important to carefully read the entire contents of this manual and become familiar with all control operations. Your Security Company Representative has recorded confidential information about your system in this manual, therefore, you should store it in a secure place. [. . . ] Contact your Security Company Representative when this condition occurs.
Bell Test
NOTE Notify your neighbors before you test the bell. Press
8
.
2.
Enter passcode:
.
3.
Press
3
.
The audible will sound for several seconds.
22
OPTIONAL FEATURES TESTING YOUR SYSTEM
Communicator Test
NOTE Your system must be monitored by a Central Station to perform this test. This test will take a while to perform.
This test is used to verify that your system is communicating with the Central Station. Press
8
.
2.
Enter passcode:
.
3.
Press
4
.
If the test passes, the Control Station will sound four (4) beeps when the test is completed. If the test fails, a communications failure trouble condition results several minutes later.
Keypad Test
To perform a keypad test: 1. Press
8
.
2.
Enter passcode:
.
3.
Press
5
.
The Control Station will briefly light all of its indicators (AWAY, STAY, NIGHT, READY, TROUBLE, FIRE, and Zones 1 - 12).
23
TESTING YOUR SYSTEM
RF Signal Strength (ZX400/ZX410 only)
If your system includes wireless sensors, then you can test the strength of signals from these sensors by performing an RF Signal Strength test. The strength of a signal can be affected by a low battery condition on the sensor or changes in the environment due furniture or appliances. 4.
Press
6
.
Enter a number between 13 and 28 to select a wireless sensor to test. The Control Station will indicate the signal strength by: Error Tone One Beep (the selected zone is not RF or is missing) (call your installation representative)
Three Beeps (acceptable) Five Beeps 5. (strong)
Repeat step 4 or press CLEAR to exit.
24
OPTIONAL FEATURES ZX200/ZX210 PROGRAMMING
ZX200/ZX210 Programming
Your system has several features which you may be able to program yourself. DO NOT attempt to program the system unless you have been properly trained on programming procedures and you fully understand these operations. There are two (2) options available:
1 Remote Connect Allows the installer to program and diagnose problems from a remote site using the telephone lines. Allows you to change any passcodes.
2
Program User Codes
Remote Connect
Contact your Security Company Representative for instructions.
Programming the User Passcodes
Your system may be programmed with up to 9 user passcodes. Consult your Security Company Representative as to which passcodes have been enabled and what Authority Level has been assigned to each one. Press
9
.
2.
Enter passcode:
.
The Ready and Trouble LEDs will flash.
3.
Press
2
.
25
ZX200/ZX210 PROGRAMMING
4.
Enter the User Passcode ID program/change.
(1 - 9) that you wish to
5.
Press ENTER .
6.
Enter new four-digit passcode:
.
Repeat steps 4 - 6 for each passcode to be programmed or press CLEAR to return to the Ready mode. If the new passcode being entered is a duplicate of an existing one, the Control Station will sound an error tone and return to the first digit location so you may try again. If you wish to make a User ID passcode inoperable, enter
0
0
0
0
as the new four-digit passcode.
26
OPTIONAL FEATURES ZX400/ZX410 PROGRAMMING
ZX400/ZX410 Programming
Your system has several features which you may be able to program yourself. DO NOT attempt to program the system unless you have been properly trained on programming procedures and you fully understand these operations. There are seven (7) options available:
1
Remote Connect
Allows the installer to program and diagnose problems from a remote site using the telephone lines. (Military format) Schedules your system to automatically turn ON at a specific day(s) and time(s). Allows you to change any passcodes.
2 3 4 5 6
Set Clock Program Automatic-ON Program Latch Key Program User Codes
Cancelling Automatic-ON Cancels the system from automatically For Today turning ON for the scheduled time for that day only. Cancelling Exit-ON For Today Cancels the system from automatically turning ON for Today 10 minutes after you leave the premises for that day only.
7
Remote Connect
Contact your Security Company Representative for instructions.
27
ZX400/ZX410 PROGRAMMING
Set Clock
The clock is set according to military time (24:00 hours). [. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and the receiver. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SENTROL ZXLED8
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SENTROL ZXLED8 will begin.