User manual SEIKO PULSAR NX01

[. . . ] Press for 2 to 3 seconds. English A PM C Select the digits to be adjusted. Set the flashing digits. A D D A 4 Return to TIME/CALENDAR mode. Selection of the digits Seconds Minutes Hour Year Month Date 12-/24-hour indication ANALOGUE TIME SETTING Second hand Hour hand Minute hand CROWN 1 Pull out when the second hand is at the 12 o'clock position. 3 Push back in to normal position when the second digits count "00" in the digital time display. English 5 CHANGEOVER OF DISPLAYS D With each press in TIME/CALENDAR mode, the display changes in the following order: Time/calendar display Calendar display Blank display English DEMONSTRATION FUNCTION The watch shows the modes and displays in order. D Press for 2 to 3 seconds in TIME/CALENDAR mode to start the demonstration. * The modes and displays are shown for 2 seconds in the following order: Time/calendar display Calendar display STOPWATCH mode TIMER mode Blank display * To stop the demonstration, press any of the buttons. 6 REGULAR ALARM mode STOPWATCH MODE The stopwatch measures up to 24 hours in 1/100 second increments for the first hour and in 1 second increments thereafter. A Press to show STOPWATCH mode. English C Start / Stop / Restart A D Reset 7 TIMER MODE The timer can be set up to 9 hours and 59 minutes in minute increments. The remaining time is displayed in seconds. A English Press to show TIMER mode. TIMER SETTING A C Press for 2 to 3 seconds. [. . . ] If the watch is left untouched with the digits flashing, it will automatically return to the TIME/CALENDAR mode in 1 to 2 minutes. Note on unusual display: While setting the time/calendar, all the segments of the display will light up if both buttons C and D are pressed at the same time. Press any one of the buttons to return to the TIME/CALENDAR mode, and then set the time/calendar again. [ANALOGUE TIME SETTING] When setting the minute hand, first advance it 4 to 5 minutes ahead of the desired time and then turn it back to the exact minute. English STOPWATCH MODE Restart and stop of the stopwatch can be repeated by pressing button C. Even if the STOPWATCH mode is changed to another while the measurement is in progress, it continues counting properly. After the stopwatch is used, however, be sure to reset it as the battery energy is consumed enormously to shorten the battery life. 15 TIMER MODE [TIMER SETTING] Before setting the desired time for the timer, reset the digits to "0:00'oo" by pressing button D. If the watch is left untouched with the digits flashing, it will automatically return to the TIMER mode in 1 to 2 minutes. [TIMER OPERATION] Restart and stop of the timer can be repeated by pressing button C. Even if the TIMER mode is changed to another while the measurement is in progress, it continues counting properly. After the timer is used, however, be sure to reset it as the battery energy is consumed enormously to shorten the battery life. English 16 REGULAR ALARM MODE [REGULAR ALARM SETTING] The flashing digits move quickly if button D is kept pressed. If the watch is left untouched with the digits flashing, it will automatically return to the REGULAR ALARM mode in 1 to 2 minutes. When the time function is displayed in the 24-hour indication, the regular alarm is also displayed in the 24-hour indication. When setting the hour digits in the 12-hour indication, check that AM/PM is properly set. Regular alarm test: The regular alarm can be tested by keeping button C pressed in the REGULAR ALARM mode. After the alarm is tested, press button C to engage/disengage the regular alarm/hourly time signal as desired. SINGLE-TIME ALARM MODE [SINGLE-TIME ALARM SETTING] When button C or D is pressed to set the single-time alarm, the single-time alarm mark "1-AL" is displayed and the single-time alarm is automatically engaged. With each press of button C or D, one minute is advanced or moved back, respectively. If the watch is left untouched in the SINGLE-TIME ALARM mode, it will automatically return to the TIME/CALENDAR mode in 20 to 30 seconds. The single-time alarm rings differently from the regular alarm. English ILLUMINATING LIGHT (Electroluminescent panel) The display remains illuminated if button B is kept pressed. When button B is pressed in the calendar or blank display of the TIME/CALENDAR mode, the time/calendar display is shown while the display is illuminated. The electroluminescent panel loses its luminance as the battery voltage gets lowered. [. . . ] Never attempt to recharge it, as this may cause battery leakage or damage to the battery. 19 TO PRESERVE THE QUALITY OF YOUR WATCH WATER RESISTANCE Water resistance (5 bar)* If "WATER RESISTANT 5 BAR" Non-water resistant is inscribed on the case back, your If "WATER RESISTANT" is not watch is designed and manuinscribed on the case back, your factured to withstand up to 5 bar watch is not water resistant, and care should be taken not to get it and is suitable for swimming, yachting and taking wet as water may damage the movement. the watch becomes wet, we suggest that you Water resistance (10 bar/15 bar/20 bar)* have it checked by an AUTHORIZED PULSAR If "WATER RESISTANT 10 BAR", DEALER or SERVICE CENTER. "WATER RESISTANT 15 BAR" or "WATER RESISTANT 20 BAR" Water resistance (3 bar) is inscribed on the case back, If "WATER RESISTANT" is inscribed on the case back, your watch is your watch is designed and manufactured to designed and manufactured to withstand up to 10 bar/15 bar/20 bar and is withstand up to 3 bar, such as acci- suitable for taking a bath, shallow diving, but not dental contact with splashes of water or rain, but it is for scuba diving. We recommend that you wear a PULSAR Diver's watch for scuba diving. [. . . ]