User manual SEIKO 4S15

[. . . ] 4206, 4207, 4217, 7002, 7009, 7019, 4S15, 7S25, 7S26, 7S35, 7S36, 7S55 To initially start your watch, swing it from side to side in a horizontal arc for about 30 seconds. 4206, 4207, 4217, 4S15 These watches can also be started by winding the crown. Note: If the watch is worn daily, SEIKO's automatic mechanism will wind the mainspring automatically through normal wrist movements. Note: When setting the minute hand of a quartz watch, advance it to a few minutes ahead of the time and then turn it back to the exact time. TIME/CALENDAR SETTING FOR MODELS WITH CALENDAR The date will change gradually between 9:00 P. M. [. . . ] (See note 1 on calendar setting. ) For some models, however, it will change instantly when the hands pass the 12 o'clock marker at midnight. For models with date calendar HOW TO USE THE WATCH Set the time/calendar following the instruction pertaining to your watch type. B 1. Turn the crown until the previous day's date appears in the calendar frame. Pull out the crown to the second click, and advance the hour and minute hands until the desired date appears. * If your watch has three hands, pull out the crown when the second hand is pointing to 12 o'clock. TIME SETTING FOR MODELS WITHOUT CALENDAR A 1. 6 D Pull out the crown all the way. * If your watch has three hands, pull out the crown when the second hand is pointing to 12 o'clock. Adjust the time by turning the crown in the desired direction. Push the crown back in to the normal position. * If your watch has three hands, push the crown back in to the normal position in accordance with a time signal for "00" seconds. 4. Push the crown back in to the normal position. * If your watch has three hands, push the crown back in to the normal position in accordance with a time signal for "00" seconds. 7 For models with day and date calendar 3 C 1. Turn the crown until the previous day's date appears in the calendar frame. Turn the crown in the opposite direction until the desired language (bilingual) for the day before the desired day appears in the calendar frame. * For Cal. We recommend that you wear a SEIKO Diver's watch while scuba diving. * Before using a water resistant 5, 10, 15 or 20 bar watch in water, make sure the crown is pushed in completely. If used in sea water, rinse the watch in fresh water and dry it completely. * When taking a shower while wearing a water resistant 5 bar watch, or taking a bath while wearing a water resistant 10, 15 or 20 bar watch, make sure to observe the following: · Do not operate the crown when the watch is wet with soapy water or shampoo. · If the watch is left in warm water, a slight time loss or gain may be caused. This condition, however, will be corrected when the watch returns to normal temperature. NOTE: Pressure in bar is a test pressure and should not be considered as corresponding to an actual diving depth since swimming movements tend to increase the pressure at a given depth. Care should also be taken when wearing and diving into water. TEMPERATURE RANGE [for analogue quartz watches only] Your watch works with stable -10°C accuracy in a temperature range of 5°C and 35°C (41°F and 95°F). Temperatures over 60°C or 140°F (50°C or 122°F for some calibres) may cause battery leakage or shorten the battery life. Do not leave your watch in very low temperatures below ­10°C or +14°F (-5°C or +23°F for some calibres) for a long time since the cold may cause a slight time loss or gain. [. . . ] Temperatures over 60°C or 140°F (50°C or 122°F for some calibres) may cause battery leakage or shorten the battery life. Do not leave your watch in very low temperatures below ­10°C or +14°F (-5°C or +23°F for some calibres) for a long time since the cold may cause a slight time loss or gain. However, the above conditions will be corrected when the watch returns to normal temperature. +60°C SHOCKS & VIBRATION General light activities will not affect your watch, but be careful not to drop your watch or hit it against hard surfaces, as this may cause damage. [. . . ]