User manual SEGA VIRTUA COP 3 DX

[. . . ] 420-6759-01UK REV 0 SERVICE MANUAL DELUXE TYPE Before using this product, read this SERVICE MANUAL carefully to understand the contents stated herein. After reading this manual, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. BEFORE USING THIS PRODUCT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1. INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION . . 2 2. [. . . ] At this time, be careful so as not to damage the wiring connected to the switch. The lamp is positioned at the end of the switch portion. TROUBLESHOOTING · Only QUALIFIED SERVICE PERSONNEL should carry out these procedures. If a problem occurs, first check the wiring connections. PROBLEMS When the main switch is turned ON, the machine is not activated CAUSE The power is not ON. COUNTERMEASURES Firmly insert the plug into the outlet. Incorrect power source/voltage. fuse) was activated due to an instantaneous overcurrent. Make sure that the power supply/voltage are correct. First, remove the cause of overcurrent and reinstate the circuit protection device to its original status. Then identify the cause of the fault on the item that caused the overcurrent & fix. The colour image on the screen is incorrect The on-screen image of the monitor sways and/or shrinks Sound is not emitted Incorrect monitor adjustment. Make appropriate adjustments. Connector connection is incorrect Make sure that the power supply and voltage are correct. SEE SECTION 5. 2. 5 Check connector connection from Base to Speaker Adjust the gun sighting alignment. SEE SECTION 3. 12 Check connector connections in the billboard case. Controller operation is not satisfactory Sighting is inaccurate due to environmental conditions, etc. Micro-switch malfunctioning Sensor BD is malfunctioning The fluorescent lamp does not light up Fluorescent lamp needs replacement The connector is disconnected 35 3. 14. CONTROLLER UNIT · · Only QUALIFIED SERVICE PERSONNEL should carry out these procedures. During daily cleaning and maintenance, check the surface of the control unit (Gun Controller) for cracks and other damage and ensure that screws are securely fastened. Loose screws, cracks, and other damage could cause harm to players and other customers if left un-repaired. · In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. Damaged wires may cause electric shock or short circuit or present a fire risk. · When securing the plastic-made parts, do not excessively fasten screws and nuts. Failure to observe this may damage the parts and cause injury due to fragments resulting from damage. In the cases where the gun's operation is not satisfactory or the gun sight deviates from the direction in which the control unit is pointed, the gun's interior parts may have been damaged. Replace the parts by disassembling the gun in the following procedure: Also, be sure to perform sighting check in the test mode when the gun parts are replaced. 3. 14. 1. OPERATION 36 3. 14. 2. CONTROL UNIT (GUN CONTROLLER) · Follow these directions carefully to avoid damaging or losing small parts. In the cases where the gun's operation is not satisfactory or the gun sight deviates from the direction in which the control unit is pointed, the gun's interior parts may have been damaged. Replace the parts by disassembling the gun using the following procedure. Note: be sure to perform sighting check in the test mode when the gun parts are replaced. 3. 14. 2. 1. REPLACING THE MICROSWITCH To replace the Gun Controller's internal components, first separate the left shell (Cover L) and right shell (Cover R). The controller's internal components are mounted on the right shell, so work with the gun lying on its right side. To replace the Weapon Change Button microswitch, first remove the Weapon Change Button from the right shell. [. . . ] 1 1 3 3 Description FRONT LID L BLANK FRONT LID BRKT BLANK M4 NUT FLG SER PAS M4 WSHR FORM A FLT BLK Component Reference (2)-3 (2)-3 92 8. 9. HOD-1070UK ASSY SPEAKER ITEM 1 101 201 301 PART NO. CPT-1061UK 130-5096 000-P00512-W HOD-60025 QTY 1 1 2 1 DESCRIPTION SPEAKER BRKT UK ASSY SERVO SPEAKER BOX M5X12 MSCR POSI PAN W/FS PAS WIRE HARN SPEAKER UNIT COMPONENT REF (101)-2 93 8. 10. VCT-1100UK ASSY CONTROLLER CABINET Item 1 2 3 5 6 7 14 18 25 26 27 32 Component Part VCT-2000UK VCT-1103 VTS-HOD-D VCT-1302UK 253-5366 JPT-3101 HOD-1304 DUT-0302UK SPY-1106 HOD-1307-A HOD-1308-A 105-5216 Qty 1 2 1 1 1 2 1 1 2 1 1 2 Description ASSY CTRL PANEL DX HOLDER VTS BOARD HOD GUN HOLDER CABI CASH BOX TUBE CLAMP JOINT PART LID COIN PATH PLATE HOLDER BRKT SIDE BRKT L BLANK SIDE BRKT R BLANK CHAIN BRKT Component Reference CONTINUED NEXT PAGE 94 CONTINUED FROM PREVIOUS PAGE ITEM 201 202 203 204 207 208 PART NUMBER 000-T00416-0B 068-441616-0B 008-T00430-0B 000-T00440-0B 000-P00420-W 030-000630-SB QTY 12 8 8 4 9 12 DESCRIPTION M4X16 MSCR TH BLK M4 WSHR 16OD FLT BLK M4X30 TMP PRF TH BLK M4X40 MSCR TH BLK M4X20 MSCR PAN W/FS PAS M6X30 BLT W/S BLK COMPONENT REFERENCE (1)-8, (7)-4 (1)-8 (12)-8 (14)-4 (3)-4, (18)-5 (25)-8, (26, 27)-4 95 8. 11. VCT-1150UK ASSY FENCE L Item 1 2 3 202 Component Part VCT-1151UK VCT-1152 VCT-1153 FAS-290034 Qty 1 1 1 6 Description FENCE FRAME L DESIGN PLATE L GUARD PLATE L M5 X15 HEX SKT LH CAP SCR STN Component Reference (3)-6 96 8. 12. [. . . ]