User manual SEGA VIRTUA COP III DELUXE TYPE

[. . . ] 1ST PRINTING APRIL `03 www. seuservice. com Deluxe Version Owner's Manual SEGA AMUSEMENTS USA, INC. 999-1769 GAME CODE: VCT VISIT OUR WEBSITE! BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain the safety: To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. [. . . ] The following is the MEDIA BOARD TEST screen for a unit with a DIMM BOARD. MEDIA BOARD TEST DIMM BOARD(TYPE3) VERSION **** STATUS GOOD CHECKING 100% DIMM TEST DIMM0 GOOD DIMM1 NONE GD-ROM GOOD PRESS TEST BUTTON TO EXIT MEDIA BOARD TEST begins immediately upon entering this test mode. If "GOOD" is displayed to the right of each item, the MEDIA BOARD components are functioning properly. After the test is complete, move the cursor to EXIT and press the TEST Button to return to the SYSTEM MENU screen. www. seuservice. com 52 SYSTEM INFORMATION Use SYSTEM INFORMATION to check version and other information for system programmes. Screens may differ depending on the type of MEDIA BOARD connected to the unit. The following is the SYSTEM INFORMATION screen for a unit with a DIMM BOARD. SYSTEMINFORMATION MAINBOARD REGION**** BOOTVERSION**** QCFIRMVERSION**** SCFIRMVERSION**** SERIALNO. *************** MEDIABOARD DIMMBOARD+GDROM MEMORYSIZE512MB FIRMVERSION**** SERIALNO. *************** PRESSTESTBUTTONTOEXIT (A) (B) (B) (B) (C) (D) (E) (F) (G) Press the TEST Button to return to the SYSTEM MENU screen. BOOT VERSION, QC FIRM VERSION, SC FIRM VERSION Version information for the MAIN BOARD system programmes. Serial number of the DIMM BOARD. (E) (F) (G) 53 www. seuservice. com JVS TEST JVS TEST is used to verify the specs of the I/O BOARD connected to the Chihiro and to run input tests. Screens may differ depending on the type of I/O BOARD connected to the unit. JVSTEST INPUTTEST NEXTNODE EXIT NODE**** NAME**************** I/OBDJVS Ver**** ********* CMDVER1. 1 JVSVER2. 0 COMVER1. 0 SWITCH2PLAYER(S)13BITS COIN2SLOT ANALOG8CH ROTARY0CH KEYCODE0 SCREENX:0Y:0CH:0 CARD0SLOT HOPPEROUT0CH DRIVEROUT6CH ANALOGOUT0CH CHARACTERCHARA:0LINE:0 BACKUP0 SELECTWITHSERVICEBUTTON ANDPRESSTESTBUTTON Use the SERVICE Button to move the cursor to the desired test item. Move the cursor to INPUT TEST and press the TEST Button to enter the INPUT TEST screen for the I/O BOARD currently displayed. When 2 or more I/O BOARDS are connected, move the cursor to NEXT NODE and press the TEST Button to enter the test screen for the next I/O BOARD. The lower the NODE number, the further away the node is from the Chihiro. Move the cursor to EXIT and press the TEST Button to return to the SYSTEM MENU screen. www. seuservice. com 54 INPUT TEST Screen JVSTEST INPUTTEST NODE1/1 SYSTEM00 PLAYER10000 PLAYER20000 COIN10000 COIN20000 ANALOG10000 ANALOG20000 ANALOG30000 ANALOG40000 ANALOG50000 ANALOG60000 ANALOG70000 ANALOG80000 PRESSTESTANDSERVICEBUTTONTOEXIT (A) (A) (A) (B) (B) (C) (C) (C) (C) (C) (C) (C) (C) On-screen values change according to the input from switches and the volume. (A) (B) SYSTEM, PLAYER Values change with input from control panel/other switches. ANALOG Displays analog values from "0000" to "FFFF". (C) Press the SERVICE and TEST Buttons simultaneously to return to the JVS TEST main screen. 55 www. seuservice. com SOUND TEST Use SOUND TEST to test sound output and to select the stereo/mono/surround setting. SOUNDTEST OUTPUTTYPESTEREO RIGHTSPEAKEROFF LEFTSPEAKEROFF EXIT (A) (B) (B) SELECTWITHSERVICEBUTTON ANDPRESSTESTBUTTON Use the SERVICE Button to move the cursor to the desired test item. (A) OUTPUT TYPE(STEREO, MONO, SURROUND) Select the sound output from the I/O PANEL audio output interface setting among STEREO, MONO and SURROUND. RIGHT/LEFT SPEAKER(ON, OFF) When set to "ON", the test sends a beep to each audio output interface. Only the word "SPEAKER" is displayed when the OUTPUT TYPE is set to "MONO", and when set to "ON", the test sends the same beep to both the left/right audio output interfaces. To test surround output, it is necessary to use a separate Audio Amp, and receive signal from a terminal not in use at the time of shipping. Note: Not available with this product. (B) Move the cursor to EXIT and press the TEST Button to return to the SYSTEM MENU screen. www. seuservice. com 56 C. R. T. COLOUR CHECK Screen Monitor COLOUR CHECK screen is displayed initially. Each of the colours (red, green and blue) is darkest at the far left and gets progressively lighter (32 steps) towards the right. Monitor brightness is set correctly if the white colour bar is black at the left edge and white at the right edge. C. R. T. TEST1/2 132 RED GREEN BLUE WHITE PRESSTESTBUTTONTOCONTINUE Press the TEST Button to proceed to the next page. [. . . ] JPT-2031 838-13144 012-P00306 DESCRIPTION SENSOR HOLDER SENSOR BD GUN SENSE TAP SCR #2 PH 3×6 NOTE 139 www. seuservice. com 18 SW UNIT (SPY-1170) ITEM NO. SPY-1171 421-8126 509-5028 220-5754 601-0042 310-5029-F20 SPY-60017 DESCRIPTION SW BRKT STICKER SWITCH PANEL SW PB 1M (MIYAMA DS-412R) VOL CONT B5KOHM (RV24YN 15S) KNOB 22 MM SUMI TUBE FF 20MM WH SW UNIT NOTE www. seuservice. com 140 19 METER UNIT (HOD-1590) ITEM NO. HOD-1591 421-6591-01 220-5617-01 220-5643-01 DESCRIPTION METER BRKT STICKER COIN METER MAG CNTR DC5V W/CONN 6P WH MAG CNTR DC5V 6P WH MZ-674-D04 NOTE 141 www. seuservice. com 20 ASSY FENCE L (VCT-1150) ITEM NO. VCT-1151 VCT-1152 VCT-1153 FAS-290034 DESCRIPTION FENCE FRAME L DESIGN PLATE L GUARD PLATE L HEX SKT LH CAP SCR STN M5×15 NOTE www. seuservice. com 142 21 ASSY FENCE R (VCT-1160) ITEM NO. [. . . ]