User manual SEGA THE HOUSE OF DEAD U R TYPE

[. . . ] Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void. Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages. This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above. VISIT OUR WEBSITE! TABLE OF CONTENTS INTRODUCTION OF THE OWNERS MANUAL GENERAL PRECAUTIONS 1. [. . . ] MEMORY Choose MEMORY TEST in the MENU mode to allow the MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked. 3. If the problem hasn't been solved yet, check the CONTROL's moves. PROJECTOR IC BOARD In the PROJECTOR ADJUSTMENT mode, check to see if the PROJECTOR adjustment is appropriately made. DATA CHECK Check such data as game play time and histogram to adjust the difficulty level, etc 6 - 8, 6 - 9, 6 - 10 6-4 6-7 6-3 6-3 PERIODIC SERVICING 6-3 6 - 8, 6 - 9 6-4 6-7 6-4 7 7 9 6-3 6-5 6 - 11 21 CAUTIONS TO BE HEEDED WHEN USING THE TEST MODE In case where multiple units are linked for communication play, exiting from the test mode causes the unit to perform the network check automatically. During this time, all of the linked units will not allow the game to be played in the normal status. Therefore, be sure not to enter the test mode if any one of the units is in play. On the other hand, if even one unit is in the test mode, make sure that other machines are not in play. 6 - 1 SWITCH UNIT AND COIN METER Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit. Adjust to the optimum sound volume by considering the environmental requirements of the installation location. If the COIN METER and the game board are electrically disconnected, game play is not possible. Open COIN CHUTE DOOR, and the switch unit shown appears. The function of each switch is as follows: 1 SOUND VOLUME SPEAKER Controls the speaker volume ofall of the machines speakers. To return to the Menu Mode without changing the setting contents, move the Curso to EXIT WITHOUT SAVE and press the TEST BUTTON. 26 6 - 9 C. R. T. TEST to cause the MONITOR to display the screen shown left, allowing MONITOR adjustment status to be checked. The color bar of each of the 4 colors, i. e. , red, green, blue, and white, is the darkest at the extreme left and becomes brighter towards the extreme right. Check if the CROSSHATCH FRAME LINE goes out of the screen and if the crosshatch lines are distorted. Press the TEST BUTTON to return to the MENU mode. 27 6 - 10 GAME ASSIGNMENTS Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and also the game settings changes (game difficulty, etc. ) can be made. SETTING CHANGE PROCEDURE Setting changes cannot be stored unless the TEST BUTTON is pressed while the arrow is on EXIT. To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON. GAME DIFFICULTY This game allows by-course difficulty level to be set in 4 levels. CONTROLLER REACTION Sets the Controller's vibration strength and off for no vibration. COUNTRY Message language. These FIGURES/ TABLES show the factory recommended settings. 28 6 - 11 COIN ASSIGNMENTS The "COIN ASSIGNMENTS" mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses "how many coins correspond to how many credits. " SETTING CHANGE PROCEDURE Setting changes cannot be stored unless the TEST BUTTON is pressed while the arrow is on EXIT. To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON. [. . . ] Using the product with dust as is accumulated can cause a fire or electrical shock. Periodically once a year, request the place of contact herin stated or the Distributer, etc. where the product was purchased from, as regards the interior cleaning. Using the product with dust as is accumulated in the interior without cleaning can cause a fire or accident. [. . . ]